Nivå 2


31 reviewed questions. Choose answers, then Calculate. Clear resets all selections. Unanswered questions score zero and remain in the percentage denominator. Open the answer review below for sources.

Ange dina värden:
Resultat:
%

Answers and sources

Reviewed 17 November 2026. Ambiguous, malformed and unverified legacy questions have been removed. Wording and answer choices have been corrected where needed. This is a study quiz, not certification of engineering or laboratory decisions.

Question 1: answer and source

A beam of span L m is simply supported at the ends. It is loaded by two equal clockwise moments at the supports. Point of contraflexure acts at

Answer: none of these

Two equal same-sense end couples produce a uniform hogging bending moment along the whole span, so the moment never changes sign and there is no point of contraflexure. Legacy key 'At mid span' was wrong.

Source 1

Question 2: answer and source

The ratio of flexibility of loose beams (b x d) placed one over the other to the flexibility of one integral beam (nb x d) is

Answer: n^2

n loose beams of depth d share the load (W/n each), so their deflection is n^2 times that of one integral beam of depth nd; flexibility ratio = n^2. Stem typo corrected ('places' to 'placed') and options use n (legacy 'h'); legacy key '1' was wrong.

Source 1

Question 3: answer and source

The earth pressure at a depth d is P; the earth pressure at depth d/2 is

Answer: 0.5P

Rankine lateral pressure p = K x gamma x z varies linearly with depth, so at d/2 it is 0.5P. Legacy key '0.25P' was wrong.

Source 1

Question 4: answer and source

A reinforced concrete column is considered as a short column, if its slenderness ratio L/b is less than

Answer: 12

IS 456: a column is short when its effective length to least lateral dimension is under 12; key unchanged.

Source 1

Question 5: answer and source

A common footing provided for two columns is called a

Answer: combined footing

A footing shared by two columns is a combined footing; key unchanged.

Source 1

Question 6: answer and source

For reinforced concrete (M15) members immersed in sea water the cover shall be

Answer: 40 mm more than the cover in the usual cases

For members totally immersed in sea water the code recommends 40 mm of additional cover. Legacy key '50 mm more' was wrong.

Source 1

Question 7: answer and source

The modulus of elasticity of steel is

Answer: 200 KN/mm^2

Structural steel E = 200 GPa = 200 kN/mm^2; key unchanged.

Source 1

Question 8: answer and source

The number of rivets for connecting a strut to a gusset plate shall not be less than

Answer: 2

IS 800 practice: at least two rivets at such a connection; key unchanged.

Source 1

Question 9: answer and source

The inclination of a lacing bar with the axis of the compression member shall not exceed

Answer: 70

IS 800 keeps lacing bars between 40 and 70 degrees to the member axis, so the maximum is 70 degrees; key unchanged.

Source 1

Question 10: answer and source

For unstiffened webs of girders, the thickness of web shall not be less than

Answer: D1/85

IS 800:1984 minimum web thickness for unstiffened girders is d1/85 (clear depth d1); key unchanged.

Source 1

Question 11: answer and source

Spacing of vertical stiffeners in a girder shall not be less than

Answer: 0.33d

IS 800 stiffener spacing limits: not less than 0.33d and not more than 1.5d; key unchanged.

Source 1

Question 12: answer and source

The maximum bending moment for a purlin may be taken as

Answer: WL/10

Purlins are designed as continuous members, so the design moment is taken as WL/10. Typo corrected ('purling' to 'purlin'); key unchanged.

Source 1

Question 13: answer and source

If the foundations of all the columns of a structure are designed on the total live and dead load basis, then

Answer: the settlement of interior columns will be more than exterior columns

Interior columns have larger tributary areas and attract more actual load, so they settle more. Legacy key 'exterior more than interior' was wrong.

Source 1

Question 14: answer and source

To minimize the effect of differential settlement, the area of footing should be designed for

Answer: dead load + fraction of live load

Dead load is always present while only a fraction of live load acts at any time, so footing areas are proportioned on dead load plus a fraction of live load; key unchanged.

Source 1

Question 15: answer and source

A reduction factor Cr, load carrying capacity of a long columns is given by

Answer: Cr = 1.25 - Le/48b

The classic reduction factor for long (slender) RC columns is Cr = 1.25 - Le/48b; key unchanged.

Source 1

Question 16: answer and source

Normally pre-stressing wires are arranged in the

Answer: lower part of the beam

Tendons are placed where the beam needs precompression, in the lower (sagging tension) zone; key unchanged.

Source 1

Question 17: answer and source

The shear stress intensity changes from the centre to the surface of the shaft with

Answer: uniform rate

Torsion shear stress tau = T.r/J grows linearly with radius, i.e. at a uniform rate from zero at the centre to maximum at the surface. Legacy key 'varying rate' was wrong.

Source 1

Question 18: answer and source

The formula T/J = N.theta/L = fs/r when applied to torsion of a closely coiled helical spring, the value of J will be calculated with

Answer: the diameter of wire of spring

J is the polar moment of the spring wire cross-section, so it uses the wire diameter. Stem notation cleaned; key unchanged.

Source 1

Question 19: answer and source

The shear stress intensity is minimum at

Answer: axis of shaft

tau is zero at the axis (r = 0) and maximum at the surface; key unchanged.

Source 1

Question 20: answer and source

A steel member which is subjected to primary tension is called

Answer: Tie

A member carrying axial tension is a tie (a strut carries compression); key unchanged.

Source 1

Question 21: answer and source

Sliding failure occurs in a solid gravity dam when

Answer: Shear friction factor is less than 1

Sliding starts when the shear friction factor (mu x vertical / horizontal force) falls below unity; the other options describe overturning or the no-tension condition. Legacy option value '1.5' corrected to 1.

Source 1

Question 22: answer and source

Mean velocity of flow in a river can be directly measured by means of

Answer: Rod floats

Rod floats extend through the depth and integrate the vertical velocity profile, giving mean velocity directly; key unchanged.

Source 1

Question 23: answer and source

The formula used to calculate maximum flood discharge for deccan catchments is

Answer: Ali Nawab Jung Bahadur formula

The Nawab Jung Bahadur formula applies to Deccan plateau catchments; key unchanged.

Source 1

Question 24: answer and source

Direct run off is the sum of

Answer: Surface run off and interflow

Direct runoff = surface runoff + prompt interflow (base flow is excluded). Legacy key 'surface run off and mass flow' was wrong.

Source 1

Question 25: answer and source

A fluid is a substance that

Answer: cannot remain at rest under the action of a shear force

A fluid has zero shear modulus: it cannot resist shear and keeps deforming under it. Typo corrected ('parctically' to 'practically'); key unchanged.

Source 1

Question 26: answer and source

In Sutro weir the discharge is proportional to

Answer: H

The Sutro (proportional) weir is shaped so that Q varies linearly with head H; key unchanged.

Source 1

Question 27: answer and source

Which of the following has highest coefficient of discharge

Answer: Venturimeter

The venturimeter's guided contraction gives the highest Cd (about 0.95-0.98); key unchanged.

Source 1

Question 28: answer and source

ML^-1 T-2 is the dimension of

Answer: Pressure

Pressure = force/area = M L^-1 T^-2; key unchanged.

Source 1

Question 29: answer and source

Cavitation is caused by

Answer: low pressure

Cavitation begins when local pressure falls below the liquid's vapour pressure; key unchanged.

Source 1

Question 30: answer and source

Number of rivets required in a joint is

Answer: load/rivet value

The rivet value is the least of shearing and bearing strength, and the number of rivets = load / rivet value; key unchanged.

Source 1

Question 31: answer and source

The point of contraflexure occurs in

Answer: over hanging beams only

The standard textbook answer: overhanging beams (a cantilever and a simply supported span without overhang keep one sign of bending moment); key unchanged.

Source 1

Change log: 17 November 2026

Original question numbers and review decisions
  • Original Q1: corrected. Two equal same-sense end couples produce a uniform hogging bending moment along the whole span, so the moment never changes sign and there is no point of contraflexure. Legacy key 'At mid span' was wrong.
  • Original Q2: corrected. n loose beams of depth d share the load (W/n each), so their deflection is n^2 times that of one integral beam of depth nd; flexibility ratio = n^2. Stem typo corrected ('places' to 'placed') and options use n (legacy 'h'); legacy key '1' was wrong.
  • Original Q3: corrected. Rankine lateral pressure p = K x gamma x z varies linearly with depth, so at d/2 it is 0.5P. Legacy key '0.25P' was wrong.
  • Original Q4: verified as keyed. IS 456: a column is short when its effective length to least lateral dimension is under 12; key unchanged.
  • Original Q5: verified as keyed. A footing shared by two columns is a combined footing; key unchanged.
  • Original Q6: corrected. For members totally immersed in sea water the code recommends 40 mm of additional cover. Legacy key '50 mm more' was wrong.
  • Original Q7: verified as keyed. Structural steel E = 200 GPa = 200 kN/mm^2; key unchanged.
  • Original Q8: verified as keyed. IS 800 practice: at least two rivets at such a connection; key unchanged.
  • Original Q9: verified as keyed. IS 800 keeps lacing bars between 40 and 70 degrees to the member axis, so the maximum is 70 degrees; key unchanged.
  • Original Q10: verified as keyed. IS 800:1984 minimum web thickness for unstiffened girders is d1/85 (clear depth d1); key unchanged.
  • Original Q11: verified as keyed. IS 800 stiffener spacing limits: not less than 0.33d and not more than 1.5d; key unchanged.
  • Original Q12: corrected. Purlins are designed as continuous members, so the design moment is taken as WL/10. Typo corrected ('purling' to 'purlin'); key unchanged.
  • Original Q13: corrected. Interior columns have larger tributary areas and attract more actual load, so they settle more. Legacy key 'exterior more than interior' was wrong.
  • Original Q14: verified as keyed. Dead load is always present while only a fraction of live load acts at any time, so footing areas are proportioned on dead load plus a fraction of live load; key unchanged.
  • Original Q15: verified as keyed. The classic reduction factor for long (slender) RC columns is Cr = 1.25 - Le/48b; key unchanged.
  • Original Q16: verified as keyed. Tendons are placed where the beam needs precompression, in the lower (sagging tension) zone; key unchanged.
  • Original Q17: corrected. Torsion shear stress tau = T.r/J grows linearly with radius, i.e. at a uniform rate from zero at the centre to maximum at the surface. Legacy key 'varying rate' was wrong.
  • Original Q18: verified as keyed. J is the polar moment of the spring wire cross-section, so it uses the wire diameter. Stem notation cleaned; key unchanged.
  • Original Q19: verified as keyed. tau is zero at the axis (r = 0) and maximum at the surface; key unchanged.
  • Original Q20: verified as keyed. A member carrying axial tension is a tie (a strut carries compression); key unchanged.
  • Original Q21: corrected. Sliding starts when the shear friction factor (mu x vertical / horizontal force) falls below unity; the other options describe overturning or the no-tension condition. Legacy option value '1.5' corrected to 1.
  • Original Q22: verified as keyed. Rod floats extend through the depth and integrate the vertical velocity profile, giving mean velocity directly; key unchanged.
  • Original Q23: verified as keyed. The Nawab Jung Bahadur formula applies to Deccan plateau catchments; key unchanged.
  • Original Q24: corrected. Direct runoff = surface runoff + prompt interflow (base flow is excluded). Legacy key 'surface run off and mass flow' was wrong.
  • Original Q25: corrected. A fluid has zero shear modulus: it cannot resist shear and keeps deforming under it. Typo corrected ('parctically' to 'practically'); key unchanged.
  • Original Q26: verified as keyed. The Sutro (proportional) weir is shaped so that Q varies linearly with head H; key unchanged.
  • Original Q27: verified as keyed. The venturimeter's guided contraction gives the highest Cd (about 0.95-0.98); key unchanged.
  • Original Q28: verified as keyed. Pressure = force/area = M L^-1 T^-2; key unchanged.
  • Original Q29: verified as keyed. Cavitation begins when local pressure falls below the liquid's vapour pressure; key unchanged.
  • Original Q30: verified as keyed. The rivet value is the least of shearing and bearing strength, and the number of rivets = load / rivet value; key unchanged.
  • Original Q31: verified as keyed. The standard textbook answer: overhanging beams (a cantilever and a simply supported span without overhang keep one sign of bending moment); key unchanged.