레벨 3


29 reviewed questions. Choose answers, then Calculate. Clear resets all selections. Unanswered questions score zero and remain in the percentage denominator. Open the answer review below for sources.

값을 입력하세요:
결과:
%

Answers and sources

Reviewed 17 November 2026. Ambiguous, malformed and unverified legacy questions have been removed. Wording and answer choices have been corrected where needed. This is a study quiz, not certification of engineering or laboratory decisions.

Question 1: answer and source

The purpose of chaplets is to

Answer: Support the cores

Chaplets are metal supports that hold cores in position in the mould cavity; legacy keyed 'directional solidification' (that is the role of chills and padding).

Question 2: answer and source

The main constituent moulding sand is

Answer: Silicon

Moulding sand is essentially silica sand (SiO2); key unchanged.

Question 3: answer and source

Shrinkage allowance is made by

Answer: Adding to external and subtracting from internal dimension

Patterns are made oversize outside (add to external) and undersize inside (subtract from internal) to offset contraction; key unchanged.

Question 4: answer and source

A large intricate heavy casting weighing two tons is to be cast. The most appropriate moulding process would be

Answer: Pit moulding

Very large, heavy castings are made in pit moulding (a pit in the foundry floor acts as the drag); legacy keyed machine moulding, which suits small to medium work.

Question 5: answer and source

A force of 250 N acts for 0.5 sec on a body of mass 20 kg. which is initially at rest. The velocity attained by the body in m/sec is

Answer: 6.25

Impulse: v = Ft/m = 250 x 0.5 / 20 = 6.25 m/s; legacy keyed 62.5.

Question 6: answer and source

The potential energy of body of mass one kg placed at a height of one metre is

Answer: 9.8 J

PE = mgh = 1 x 9.8 x 1 = 9.8 J; key unchanged.

Question 7: answer and source

The unit of energy is S.I. system is

Answer: Joule

SI unit of energy is the joule; key unchanged.

Question 8: answer and source

A 98N force is sufficient to pull a 100 kg block on horizontal table at a uniform speed. If g=9.8 m/s^2, the coefficient of friction is

Answer: 0.1

mu = F/N = 98/(100 x 9.8) = 0.1; key unchanged. Fixed misprint 'uniforce'.

Question 9: answer and source

In a lifting machine, a load of 240 N is being raised and the velocity ratio is 20. If the efficiency of the machine is 40%, the effort is equal to

Answer: 30N

MA = efficiency x VR = 0.4 x 20 = 8; effort = 240/8 = 30 N; key unchanged.

Question 10: answer and source

Centrifugal tension in belts

Answer: Reduce power transmission

Centrifugal tension adds to total tension without adding to effective pull, and at speed it reduces grip, so it reduces power transmission; key unchanged.

Question 11: answer and source

In V-belts the contact between the pulley and the belt is at the

Answer: Sides only

A V-belt wedges against the groove sides and should never bottom; legacy keyed 'Bottom only'.

Question 12: answer and source

At half load the steam consumption in the throttle governed engine is 'S1' and in a cut off governed engine it is 'S2' under similar condition

Answer: S2<S1

Cut-off governing is more economical at part load than throttle governing, so S2 < S1; legacy keyed S2 > S1.

Question 13: answer and source

For gas turbines, the compressors used are

Answer: Axial flow type

Gas turbine plants use axial-flow (sometimes centrifugal) compressors, axial being the standard answer; legacy keyed reciprocating.

Question 14: answer and source

In vapour compression refrigeration system, compressor is used because

Answer: It makes possible to remove heat from refrigerant at atmospheric temperature

The compressor raises the refrigerant's pressure and temperature so heat can be rejected to the surroundings in the condenser; legacy keyed 'removes thermal properties' (nonsense). Option wording cleaned.

Question 15: answer and source

In a mechanical refrigeration system, the highest temperature of refrigerant occurs

Answer: Between compressor and condenser

The hot discharge gas between compressor and condenser is the hottest point; key unchanged. Fixed misprints 'evaporater'/'value'.

Question 16: answer and source

A sine bar cannot be used without

Answer: Slip gauge

A sine bar is set by building the height h = L sin(theta) with slip gauges; legacy keyed angle gauge.

Question 17: answer and source

Which one of the following is not part of combination set?

Answer: Dial gauge

A combination set comprises the stock (square head), steel rule (scale), centre head and bevel protractor; a dial gauge is not part of it; legacy keyed 'Scale'.

Question 18: answer and source

For machining the flange of a 90 elbow on a lathe, the following holding device is used.

Answer: Angle plate

An angle plate (bolted to the face plate) holds the elbow so the flange face can be machined square; legacy keyed face plate.

Question 19: answer and source

The purpose of tumbler gears in lathe is to

Answer: Give desired direction of movement to the lathe carriage

Tumbler gears reverse the lead-screw/feed direction to move the carriage either way; key unchanged.

Question 20: answer and source

Permeability, in relation to moulding sands, is high for

Answer: coarse grains

Coarse grains leave larger void passages, so higher permeability; key unchanged.

Question 21: answer and source

Gantt chart is used for

Answer: production scheduling

Gantt charts lay jobs against time for production scheduling; key unchanged. Fixed misprint 'Gnatt'.

Question 22: answer and source

Pipes subjected to high pressures are generally made by

Answer: centrifugal casting

Centrifugal casting gives dense, defect-free pipe walls suited to high pressure; key unchanged.

Question 23: answer and source

Cobalt is added to high speed steel (H.S.S.) to

Answer: increases hot hardness

Cobalt raises the red (hot) hardness of high speed steel; key unchanged.

Question 24: answer and source

During cold working, metals are worked

Answer: below their recrystallization temperature

Cold working is deformation below the recrystallization temperature; key unchanged. Fixed misprints.

Question 25: answer and source

Cores are used in a mould to make it

Answer: hollow

Cores form the hollow (internal) portions of a casting; key unchanged.

Question 26: answer and source

Angle plate is used for

Answer: cutting angles in a shaper

An angle plate holds the job at a right angle for machining, e.g. cutting angles on a shaper; key unchanged.

Question 27: answer and source

A vent wire is used in

Answer: Foundry

A vent wire pokes vent holes in the mould sand in foundry work; legacy keyed hot forging.

Question 28: answer and source

The purpose of using flux in soldering is to

Answer: Prevent oxide formation

Flux cleans the surfaces and prevents oxide formation so the solder wets the joint; legacy keyed fluidity.

Question 29: answer and source

Cope in foundry practice refers to

Answer: Top half of moulding box

Cope = top half, drag = bottom half, cheek = middle; key unchanged.

Change log: 17 November 2026

Original question numbers and review decisions
  • Original Q1: verified as keyed. Chaplets are metal supports that hold cores in position in the mould cavity; legacy keyed 'directional solidification' (that is the role of chills and padding).
  • Original Q2: verified as keyed. Moulding sand is essentially silica sand (SiO2); key unchanged.
  • Original Q3: verified as keyed. Patterns are made oversize outside (add to external) and undersize inside (subtract from internal) to offset contraction; key unchanged.
  • Original Q4: verified as keyed. Very large, heavy castings are made in pit moulding (a pit in the foundry floor acts as the drag); legacy keyed machine moulding, which suits small to medium work.
  • Original Q5: verified as keyed. Impulse: v = Ft/m = 250 x 0.5 / 20 = 6.25 m/s; legacy keyed 62.5.
  • Original Q6: verified as keyed. PE = mgh = 1 x 9.8 x 1 = 9.8 J; key unchanged.
  • Original Q7: verified as keyed. SI unit of energy is the joule; key unchanged.
  • Original Q8: verified as keyed. mu = F/N = 98/(100 x 9.8) = 0.1; key unchanged. Fixed misprint 'uniforce'.
  • Original Q9: verified as keyed. MA = efficiency x VR = 0.4 x 20 = 8; effort = 240/8 = 30 N; key unchanged.
  • Original Q11: verified as keyed. Centrifugal tension adds to total tension without adding to effective pull, and at speed it reduces grip, so it reduces power transmission; key unchanged.
  • Original Q12: verified as keyed. A V-belt wedges against the groove sides and should never bottom; legacy keyed 'Bottom only'.
  • Original Q13: verified as keyed. Cut-off governing is more economical at part load than throttle governing, so S2 < S1; legacy keyed S2 > S1.
  • Original Q14: verified as keyed. Gas turbine plants use axial-flow (sometimes centrifugal) compressors, axial being the standard answer; legacy keyed reciprocating.
  • Original Q15: verified as keyed. The compressor raises the refrigerant's pressure and temperature so heat can be rejected to the surroundings in the condenser; legacy keyed 'removes thermal properties' (nonsense). Option wording cleaned.
  • Original Q16: verified as keyed. The hot discharge gas between compressor and condenser is the hottest point; key unchanged. Fixed misprints 'evaporater'/'value'.
  • Original Q17: verified as keyed. A sine bar is set by building the height h = L sin(theta) with slip gauges; legacy keyed angle gauge.
  • Original Q18: verified as keyed. A combination set comprises the stock (square head), steel rule (scale), centre head and bevel protractor; a dial gauge is not part of it; legacy keyed 'Scale'.
  • Original Q19: verified as keyed. An angle plate (bolted to the face plate) holds the elbow so the flange face can be machined square; legacy keyed face plate.
  • Original Q20: verified as keyed. Tumbler gears reverse the lead-screw/feed direction to move the carriage either way; key unchanged.
  • Original Q21: verified as keyed. Coarse grains leave larger void passages, so higher permeability; key unchanged.
  • Original Q23: verified as keyed. Gantt charts lay jobs against time for production scheduling; key unchanged. Fixed misprint 'Gnatt'.
  • Original Q24: verified as keyed. Centrifugal casting gives dense, defect-free pipe walls suited to high pressure; key unchanged.
  • Original Q25: verified as keyed. Cobalt raises the red (hot) hardness of high speed steel; key unchanged.
  • Original Q26: verified as keyed. Cold working is deformation below the recrystallization temperature; key unchanged. Fixed misprints.
  • Original Q27: verified as keyed. Cores form the hollow (internal) portions of a casting; key unchanged.
  • Original Q28: verified as keyed. An angle plate holds the job at a right angle for machining, e.g. cutting angles on a shaper; key unchanged.
  • Original Q29: verified as keyed. A vent wire pokes vent holes in the mould sand in foundry work; legacy keyed hot forging.
  • Original Q30: verified as keyed. Flux cleans the surfaces and prevents oxide formation so the solder wets the joint; legacy keyed fluidity.
  • Original Q31: verified as keyed. Cope = top half, drag = bottom half, cheek = middle; key unchanged.
  • Original Q10: For equal kinetic energy p = sqrt(2m.KE), so the ratio is sqrt(10):sqrt(4) = 1.58:1, which is not among the options (1:2, 3:1, 4:1, 1:16); the keyed 4:1 has no derivation. Dropped as unfixable.
  • Original Q22: Discontinuous chips are characteristic of brittle materials such as cast iron and brass; none of the legacy options (carbon steel, copper, steel at high speed, mild steel - all ductile, continuous-chip materials) is correct. Dropped as unfixable.