Stufe 3


29 reviewed questions. Choose answers, then Calculate. Clear resets all selections. Unanswered questions score zero and remain in the percentage denominator. Open the answer review below for sources.

Geben Sie Ihre Werte ein:
Ergebnisse:
%

Answers and sources

Reviewed 17 November 2026. Ambiguous, malformed and unverified legacy questions have been removed. Wording and answer choices have been corrected where needed. This is a study quiz, not certification of engineering or laboratory decisions.

Question 1: answer and source

The purpose of chaplets is to

Answer: Support the cores

Chaplets are metal supports that hold cores in position in the mould cavity; legacy keyed 'directional solidification' (that is the role of chills and padding).

Question 2: answer and source

The main constituent moulding sand is

Answer: Silicon

Moulding sand is essentially silica sand (SiO2); key unchanged.

Question 3: answer and source

Shrinkage allowance is made by

Answer: Adding to external and subtracting from internal dimension

Patterns are made oversize outside (add to external) and undersize inside (subtract from internal) to offset contraction; key unchanged.

Question 4: answer and source

A large intricate heavy casting weighing two tons is to be cast. The most appropriate moulding process would be

Answer: Pit moulding

Very large, heavy castings are made in pit moulding (a pit in the foundry floor acts as the drag); legacy keyed machine moulding, which suits small to medium work.

Question 5: answer and source

A force of 250 N acts for 0.5 sec on a body of mass 20 kg. which is initially at rest. The velocity attained by the body in m/sec is

Answer: 6.25

Impulse: v = Ft/m = 250 x 0.5 / 20 = 6.25 m/s; legacy keyed 62.5.

Question 6: answer and source

The potential energy of body of mass one kg placed at a height of one metre is

Answer: 9.8 J

PE = mgh = 1 x 9.8 x 1 = 9.8 J; key unchanged.

Question 7: answer and source

The unit of energy is S.I. system is

Answer: Joule

SI unit of energy is the joule; key unchanged.

Question 8: answer and source

A 98N force is sufficient to pull a 100 kg block on horizontal table at a uniform speed. If g=9.8 m/s^2, the coefficient of friction is

Answer: 0.1

mu = F/N = 98/(100 x 9.8) = 0.1; key unchanged. Fixed misprint 'uniforce'.

Question 9: answer and source

In a lifting machine, a load of 240 N is being raised and the velocity ratio is 20. If the efficiency of the machine is 40%, the effort is equal to

Answer: 30N

MA = efficiency x VR = 0.4 x 20 = 8; effort = 240/8 = 30 N; key unchanged.

Question 10: answer and source

Centrifugal tension in belts

Answer: Reduce power transmission

Centrifugal tension adds to total tension without adding to effective pull, and at speed it reduces grip, so it reduces power transmission; key unchanged.

Question 11: answer and source

In V-belts the contact between the pulley and the belt is at the

Answer: Sides only

A V-belt wedges against the groove sides and should never bottom; legacy keyed 'Bottom only'.

Question 12: answer and source

At half load the steam consumption in the throttle governed engine is 'S1' and in a cut off governed engine it is 'S2' under similar condition

Answer: S2<S1

Cut-off governing is more economical at part load than throttle governing, so S2 < S1; legacy keyed S2 > S1.

Question 13: answer and source

For gas turbines, the compressors used are

Answer: Axial flow type

Gas turbine plants use axial-flow (sometimes centrifugal) compressors, axial being the standard answer; legacy keyed reciprocating.

Question 14: answer and source

In vapour compression refrigeration system, compressor is used because

Answer: It makes possible to remove heat from refrigerant at atmospheric temperature

The compressor raises the refrigerant's pressure and temperature so heat can be rejected to the surroundings in the condenser; legacy keyed 'removes thermal properties' (nonsense). Option wording cleaned.

Question 15: answer and source

In a mechanical refrigeration system, the highest temperature of refrigerant occurs

Answer: Between compressor and condenser

The hot discharge gas between compressor and condenser is the hottest point; key unchanged. Fixed misprints 'evaporater'/'value'.

Question 16: answer and source

A sine bar cannot be used without

Answer: Slip gauge

A sine bar is set by building the height h = L sin(theta) with slip gauges; legacy keyed angle gauge.

Question 17: answer and source

Which one of the following is not part of combination set?

Answer: Dial gauge

A combination set comprises the stock (square head), steel rule (scale), centre head and bevel protractor; a dial gauge is not part of it; legacy keyed 'Scale'.

Question 18: answer and source

For machining the flange of a 90 elbow on a lathe, the following holding device is used.

Answer: Angle plate

An angle plate (bolted to the face plate) holds the elbow so the flange face can be machined square; legacy keyed face plate.

Question 19: answer and source

The purpose of tumbler gears in lathe is to

Answer: Give desired direction of movement to the lathe carriage

Tumbler gears reverse the lead-screw/feed direction to move the carriage either way; key unchanged.

Question 20: answer and source

Permeability, in relation to moulding sands, is high for

Answer: coarse grains

Coarse grains leave larger void passages, so higher permeability; key unchanged.

Question 21: answer and source

Gantt chart is used for

Answer: production scheduling

Gantt charts lay jobs against time for production scheduling; key unchanged. Fixed misprint 'Gnatt'.

Question 22: answer and source

Pipes subjected to high pressures are generally made by

Answer: centrifugal casting

Centrifugal casting gives dense, defect-free pipe walls suited to high pressure; key unchanged.

Question 23: answer and source

Cobalt is added to high speed steel (H.S.S.) to

Answer: increases hot hardness

Cobalt raises the red (hot) hardness of high speed steel; key unchanged.

Question 24: answer and source

During cold working, metals are worked

Answer: below their recrystallization temperature

Cold working is deformation below the recrystallization temperature; key unchanged. Fixed misprints.

Question 25: answer and source

Cores are used in a mould to make it

Answer: hollow

Cores form the hollow (internal) portions of a casting; key unchanged.

Question 26: answer and source

Angle plate is used for

Answer: cutting angles in a shaper

An angle plate holds the job at a right angle for machining, e.g. cutting angles on a shaper; key unchanged.

Question 27: answer and source

A vent wire is used in

Answer: Foundry

A vent wire pokes vent holes in the mould sand in foundry work; legacy keyed hot forging.

Question 28: answer and source

The purpose of using flux in soldering is to

Answer: Prevent oxide formation

Flux cleans the surfaces and prevents oxide formation so the solder wets the joint; legacy keyed fluidity.

Question 29: answer and source

Cope in foundry practice refers to

Answer: Top half of moulding box

Cope = top half, drag = bottom half, cheek = middle; key unchanged.

Change log: 17 November 2026

Original question numbers and review decisions
  • Original Q1: verified as keyed. Chaplets are metal supports that hold cores in position in the mould cavity; legacy keyed 'directional solidification' (that is the role of chills and padding).
  • Original Q2: verified as keyed. Moulding sand is essentially silica sand (SiO2); key unchanged.
  • Original Q3: verified as keyed. Patterns are made oversize outside (add to external) and undersize inside (subtract from internal) to offset contraction; key unchanged.
  • Original Q4: verified as keyed. Very large, heavy castings are made in pit moulding (a pit in the foundry floor acts as the drag); legacy keyed machine moulding, which suits small to medium work.
  • Original Q5: verified as keyed. Impulse: v = Ft/m = 250 x 0.5 / 20 = 6.25 m/s; legacy keyed 62.5.
  • Original Q6: verified as keyed. PE = mgh = 1 x 9.8 x 1 = 9.8 J; key unchanged.
  • Original Q7: verified as keyed. SI unit of energy is the joule; key unchanged.
  • Original Q8: verified as keyed. mu = F/N = 98/(100 x 9.8) = 0.1; key unchanged. Fixed misprint 'uniforce'.
  • Original Q9: verified as keyed. MA = efficiency x VR = 0.4 x 20 = 8; effort = 240/8 = 30 N; key unchanged.
  • Original Q11: verified as keyed. Centrifugal tension adds to total tension without adding to effective pull, and at speed it reduces grip, so it reduces power transmission; key unchanged.
  • Original Q12: verified as keyed. A V-belt wedges against the groove sides and should never bottom; legacy keyed 'Bottom only'.
  • Original Q13: verified as keyed. Cut-off governing is more economical at part load than throttle governing, so S2 < S1; legacy keyed S2 > S1.
  • Original Q14: verified as keyed. Gas turbine plants use axial-flow (sometimes centrifugal) compressors, axial being the standard answer; legacy keyed reciprocating.
  • Original Q15: verified as keyed. The compressor raises the refrigerant's pressure and temperature so heat can be rejected to the surroundings in the condenser; legacy keyed 'removes thermal properties' (nonsense). Option wording cleaned.
  • Original Q16: verified as keyed. The hot discharge gas between compressor and condenser is the hottest point; key unchanged. Fixed misprints 'evaporater'/'value'.
  • Original Q17: verified as keyed. A sine bar is set by building the height h = L sin(theta) with slip gauges; legacy keyed angle gauge.
  • Original Q18: verified as keyed. A combination set comprises the stock (square head), steel rule (scale), centre head and bevel protractor; a dial gauge is not part of it; legacy keyed 'Scale'.
  • Original Q19: verified as keyed. An angle plate (bolted to the face plate) holds the elbow so the flange face can be machined square; legacy keyed face plate.
  • Original Q20: verified as keyed. Tumbler gears reverse the lead-screw/feed direction to move the carriage either way; key unchanged.
  • Original Q21: verified as keyed. Coarse grains leave larger void passages, so higher permeability; key unchanged.
  • Original Q23: verified as keyed. Gantt charts lay jobs against time for production scheduling; key unchanged. Fixed misprint 'Gnatt'.
  • Original Q24: verified as keyed. Centrifugal casting gives dense, defect-free pipe walls suited to high pressure; key unchanged.
  • Original Q25: verified as keyed. Cobalt raises the red (hot) hardness of high speed steel; key unchanged.
  • Original Q26: verified as keyed. Cold working is deformation below the recrystallization temperature; key unchanged. Fixed misprints.
  • Original Q27: verified as keyed. Cores form the hollow (internal) portions of a casting; key unchanged.
  • Original Q28: verified as keyed. An angle plate holds the job at a right angle for machining, e.g. cutting angles on a shaper; key unchanged.
  • Original Q29: verified as keyed. A vent wire pokes vent holes in the mould sand in foundry work; legacy keyed hot forging.
  • Original Q30: verified as keyed. Flux cleans the surfaces and prevents oxide formation so the solder wets the joint; legacy keyed fluidity.
  • Original Q31: verified as keyed. Cope = top half, drag = bottom half, cheek = middle; key unchanged.
  • Original Q10: For equal kinetic energy p = sqrt(2m.KE), so the ratio is sqrt(10):sqrt(4) = 1.58:1, which is not among the options (1:2, 3:1, 4:1, 1:16); the keyed 4:1 has no derivation. Dropped as unfixable.
  • Original Q22: Discontinuous chips are characteristic of brittle materials such as cast iron and brass; none of the legacy options (carbon steel, copper, steel at high speed, mild steel - all ductile, continuous-chip materials) is correct. Dropped as unfixable.