Nível 1
30 reviewed questions. Choose answers, then Calculate. Clear resets all selections. Unanswered questions score zero and remain in the percentage denominator. Open the answer review below for sources.
Answers and sources
Reviewed 17 November 2026. Ambiguous, malformed and unverified legacy questions have been removed. Wording and answer choices have been corrected where needed. This is a study quiz, not certification of engineering or laboratory decisions.
Question 1: answer and source
A rectangular beam of length l supported at its two ends carries a central concentrated load W at its centre. The maximum deflection occurs
Answer: at the mid span
For a simply supported beam with a central point load, deflection is maximum at mid-span. Stem variable 'I' corrected to 'l' (length); key unchanged.
Question 2: answer and source
If the depth is kept constant for a beam of uniform strength then its width will vary proportional to
Answer: M
At constant depth, bending stress fixes b proportional to the bending moment M; key unchanged.
Question 3: answer and source
A beam of length l is bent into an arc of a circle of radius R. The maximum deflection of the beam is
Answer: l^2/8R
The deflection is the sagitta of the arc: s = l^2/8R (small-deflection approximation). Legacy stem was garbled ('deflects into a uniform strength... width proportional to') and option D 'l^2/2d' corrected to 'l^2/2R'; question repaired to the intended geometry.
Question 4: answer and source
The longitudinal stress in a thin cylindrical shell is
Answer: Pd/4t
Thin cylinder: hoop stress = Pd/2t, longitudinal stress = Pd/4t; key unchanged.
Question 5: answer and source
The ratio of maximum shear stress and average shear stress for a rectangular section is
Answer: 1.5
Rectangular section: tau_max = 3V/2A = 1.5 x tau_avg; key unchanged.
Question 6: answer and source
A fixed beam of span L carries a central point load W. The maximum sagging bending moment in the beam is
Answer: WL/8
Fixed-fixed beam with central point load: WL/8 hogging at each support and WL/8 sagging under the load. Legacy key 'WL/4' is the simply supported value and was wrong.
Question 7: answer and source
Air entrainment in the concrete increases
Answer: workability
Air entrainment improves workability (and freeze-thaw durability); compressive strength falls with entrained air. Legacy key 'strength' was wrong.
Question 8: answer and source
The relation between modulus of rupture Fcr and characteristic strength of concrete Fck is given by
Answer: Fcr = 0.7 S Fck
IS 456 gives fcr = 0.7 x sqrt(fck) (the 'S' in the options stands for the square root). Legacy key '0.35 S Fck' was wrong.
Question 9: answer and source
The compressive strength of 100 mm cube as compared to 150 mm cube is always
Answer: more
Smaller cubes test stronger: platen restraint confines the whole 100 mm cube, so it gives higher results than a 150 mm cube. Legacy key 'equal' was wrong.
Question 10: answer and source
For a slab supported on its four edges with corners held down and loaded uniformly, the Marcus correction factor to the moments obtained by Grashoff Rankine's theory
Answer: is always less than 1
Marcus's correction reduces the Grashof-Rankine moments, so the factor is always less than 1. Legacy key 'greater than 1' was wrong.
Question 11: answer and source
For bars in tension a standard hook has an anchorage value equivalent to a straight length of
Answer: 16
A standard hook is counted as 16 bar diameters of anchorage (16d). Option text clarified ('strength length' to 'straight length'); key unchanged.
Question 12: answer and source
Cube strength of controlled concrete to be used for pre-tensioned and post-tensioned work respectively should not be less than
Answer: 420 Kg/cm^2 and 350 Kg/cm^2
Pre-tensioned work requires the higher grade: about 420 kg/cm^2 (42 MPa) for pre-tensioning and 350 kg/cm^2 (35 MPa) for post-tensioning. Legacy key '420 and 530' was wrong.
Question 13: answer and source
The creep strains are
Answer: caused due to dead loads only
Creep develops under sustained (permanent) load, i.e. dead load; keyed answer confirmed against the BPSC AE 2019 official paper. Key unchanged.
Question 14: answer and source
Ratio of compressive strength to tensile strength of concrete
Answer: increases with age
Tensile strength gains proportionally slower than compressive strength with age, so the ratio increases; key unchanged.
Question 15: answer and source
In limit state design of concrete for flexure, the area of stress block is taken as
Answer: 0.36 Fck Xu
IS 456 stress block: resultant compressive force = 0.36 fck.xu per unit width; key unchanged.
Question 16: answer and source
The fineness modulus of the fine aggregate is in the range of
Answer: 2.0 to 3.5
Fine aggregates run an FM of roughly 2-4 (commonly quoted 2.0-3.5 for sand). Stem typo corrected ('fitness' to 'fineness'); key unchanged.
Question 17: answer and source
According to IS:456, the maximum reinforcement in a column is
Answer: 6%
IS 456 clause 26.5.3.1 caps column longitudinal reinforcement at 6% of the cross-section; key unchanged.
Question 18: answer and source
The minimum cover in a slab should neither be less than the diameter of bar nor less than
Answer: 15 mm
IS 456 nominal cover: not less than the bar diameter and not less than 15 mm; key unchanged.
Question 19: answer and source
If the permissible stress in steel in tension is 140 N/mm^2, permissible stress in concrete in bending compression is 5 N/mm^2. Then the depth of neutral axis for a singly reinforced rectangular balanced section will be
Answer: 0.40 d
m = 280/(3 x 5) = 18.67; k = m.cbc/(st + m.cbc) = 93.3/233.3 = 0.40, so the neutral axis is at 0.40d; key unchanged.
Question 20: answer and source
The slab is designed as one way if the ratio of long span to short span is
Answer: greater than 2
ly/lx greater than 2 makes a slab one-way (IS 456 Annex D); key unchanged.
Question 21: answer and source
In any beam when the moment of inertia about the neutral axis is doubled, its deflection is
Answer: halved
Deflection is inversely proportional to EI, so doubling I halves the deflection; key unchanged.
Question 22: answer and source
The limits of percentage of the longitudinal reinforcement in a column is given by
Answer: 0.8% to 6%
IS 456 clause 26.5.3.1: not less than 0.8% and not more than 6%; key unchanged.
Question 23: answer and source
A rigid prop provided for a beam
Answer: brings the deflection at the prop to zero
A rigid support prevents vertical movement at its section; key unchanged.
Question 24: answer and source
In a simply supported beam AB with a concentrated load W at a distance 'a' from support A and 'b' from support B, the deflection under the load is
Answer: Wa^2 b^2 / 3EIL
Standard result: deflection under an eccentric point load = W a^2 b^2 / (3EIL); key unchanged.
Question 25: answer and source
For the design of retaining walls the minimum factor of safety against over-turning is taken as
Answer: 2.5
FoS against overturning is at least 2.0 (sliding is 1.5); key unchanged.
Question 26: answer and source
A cantilever beam is loaded by a point load at the free end. It is likely to fail by B.M.
Answer: at support
The bending moment in a cantilever is maximum at the fixed support; key unchanged.
Question 27: answer and source
The distance between centre lines of a broad gauge is 1.686m. The most economic length of sleeper for efficient distribution of B.M. is
Answer: 2.866 m
The sleeper extends about 0.59 m beyond each rail centre (c/c + 1.18 m = 1.686 + 1.18 = 2.866 m); key unchanged.
Question 28: answer and source
In a simply supported beam of span L carrying an eccentric couple M acting at a distance A from the left support, the reaction induced at the support is
Answer: M/L
A pure couple is balanced by an equal and opposite couple M/L x L, so each support reaction is M/L; stem typo corrected ('included' to 'induced'); key unchanged.
Question 29: answer and source
The section modulus of square section of side A is
Answer: a^3/6
Z = I/ymax = (a^4/12)/(a/2) = a^3/6; key unchanged.
Question 30: answer and source
The minimum percentage of mild steel reinforcement in walls of RCC water tanks of 450 mm thick is about
Answer: 0.20
IS 3370 minimum reinforcement tapers from 0.3% at 100 mm thickness to 0.2% at 450 mm thickness; key unchanged.
Change log: 17 November 2026
Original question numbers and review decisions
- Original Q1: corrected. For a simply supported beam with a central point load, deflection is maximum at mid-span. Stem variable 'I' corrected to 'l' (length); key unchanged.
- Original Q2: verified as keyed. At constant depth, bending stress fixes b proportional to the bending moment M; key unchanged.
- Original Q3: corrected. The deflection is the sagitta of the arc: s = l^2/8R (small-deflection approximation). Legacy stem was garbled ('deflects into a uniform strength... width proportional to') and option D 'l^2/2d' corrected to 'l^2/2R'; question repaired to the intended geometry.
- Original Q4: verified as keyed. Thin cylinder: hoop stress = Pd/2t, longitudinal stress = Pd/4t; key unchanged.
- Original Q5: verified as keyed. Rectangular section: tau_max = 3V/2A = 1.5 x tau_avg; key unchanged.
- Original Q6: corrected. Fixed-fixed beam with central point load: WL/8 hogging at each support and WL/8 sagging under the load. Legacy key 'WL/4' is the simply supported value and was wrong.
- Original Q7: corrected. Air entrainment improves workability (and freeze-thaw durability); compressive strength falls with entrained air. Legacy key 'strength' was wrong.
- Original Q8: corrected. IS 456 gives fcr = 0.7 x sqrt(fck) (the 'S' in the options stands for the square root). Legacy key '0.35 S Fck' was wrong.
- Original Q9: corrected. Smaller cubes test stronger: platen restraint confines the whole 100 mm cube, so it gives higher results than a 150 mm cube. Legacy key 'equal' was wrong.
- Original Q10: corrected. Marcus's correction reduces the Grashof-Rankine moments, so the factor is always less than 1. Legacy key 'greater than 1' was wrong.
- Original Q11: corrected. A standard hook is counted as 16 bar diameters of anchorage (16d). Option text clarified ('strength length' to 'straight length'); key unchanged.
- Original Q12: corrected. Pre-tensioned work requires the higher grade: about 420 kg/cm^2 (42 MPa) for pre-tensioning and 350 kg/cm^2 (35 MPa) for post-tensioning. Legacy key '420 and 530' was wrong.
- Original Q13: verified as keyed. Creep develops under sustained (permanent) load, i.e. dead load; keyed answer confirmed against the BPSC AE 2019 official paper. Key unchanged.
- Original Q14: verified as keyed. Tensile strength gains proportionally slower than compressive strength with age, so the ratio increases; key unchanged.
- Original Q15: verified as keyed. IS 456 stress block: resultant compressive force = 0.36 fck.xu per unit width; key unchanged.
- Original Q16: corrected. Fine aggregates run an FM of roughly 2-4 (commonly quoted 2.0-3.5 for sand). Stem typo corrected ('fitness' to 'fineness'); key unchanged.
- Original Q17: verified as keyed. IS 456 clause 26.5.3.1 caps column longitudinal reinforcement at 6% of the cross-section; key unchanged.
- Original Q18: verified as keyed. IS 456 nominal cover: not less than the bar diameter and not less than 15 mm; key unchanged.
- Original Q19: verified as keyed. m = 280/(3 x 5) = 18.67; k = m.cbc/(st + m.cbc) = 93.3/233.3 = 0.40, so the neutral axis is at 0.40d; key unchanged.
- Original Q20: verified as keyed. ly/lx greater than 2 makes a slab one-way (IS 456 Annex D); key unchanged.
- Original Q21: verified as keyed. Deflection is inversely proportional to EI, so doubling I halves the deflection; key unchanged.
- Original Q22: verified as keyed. IS 456 clause 26.5.3.1: not less than 0.8% and not more than 6%; key unchanged.
- Original Q23: verified as keyed. A rigid support prevents vertical movement at its section; key unchanged.
- Original Q24: verified as keyed. Standard result: deflection under an eccentric point load = W a^2 b^2 / (3EIL); key unchanged.
- Original Q25: verified as keyed. FoS against overturning is at least 2.0 (sliding is 1.5); key unchanged.
- Original Q26: verified as keyed. The bending moment in a cantilever is maximum at the fixed support; key unchanged.
- Original Q27: verified as keyed. The sleeper extends about 0.59 m beyond each rail centre (c/c + 1.18 m = 1.686 + 1.18 = 2.866 m); key unchanged.
- Original Q28: corrected. A pure couple is balanced by an equal and opposite couple M/L x L, so each support reaction is M/L; stem typo corrected ('included' to 'induced'); key unchanged.
- Original Q30: verified as keyed. Z = I/ymax = (a^4/12)/(a/2) = a^3/6; key unchanged.
- Original Q31: verified as keyed. IS 3370 minimum reinforcement tapers from 0.3% at 100 mm thickness to 0.2% at 450 mm thickness; key unchanged.
- Original Q29: Stem lost its beam data in the legacy file (no loading given), so no option, including the keyed 140 KNm, can be verified or computed. Dropped as unfixable.