第 1 级


30 reviewed questions. Choose answers, then Calculate. Clear resets all selections. Unanswered questions score zero and remain in the percentage denominator. Open the answer review below for sources.

请输入数值:
结果:
%

Answers and sources

Reviewed 17 November 2026. Ambiguous, malformed and unverified legacy questions have been removed. Wording and answer choices have been corrected where needed. This is a study quiz, not certification of engineering or laboratory decisions.

Question 1: answer and source

A rectangular beam of length l supported at its two ends carries a central concentrated load W at its centre. The maximum deflection occurs

Answer: at the mid span

For a simply supported beam with a central point load, deflection is maximum at mid-span. Stem variable 'I' corrected to 'l' (length); key unchanged.

Source 1

Question 2: answer and source

If the depth is kept constant for a beam of uniform strength then its width will vary proportional to

Answer: M

At constant depth, bending stress fixes b proportional to the bending moment M; key unchanged.

Source 1

Question 3: answer and source

A beam of length l is bent into an arc of a circle of radius R. The maximum deflection of the beam is

Answer: l^2/8R

The deflection is the sagitta of the arc: s = l^2/8R (small-deflection approximation). Legacy stem was garbled ('deflects into a uniform strength... width proportional to') and option D 'l^2/2d' corrected to 'l^2/2R'; question repaired to the intended geometry.

Source 1

Question 4: answer and source

The longitudinal stress in a thin cylindrical shell is

Answer: Pd/4t

Thin cylinder: hoop stress = Pd/2t, longitudinal stress = Pd/4t; key unchanged.

Source 1

Question 5: answer and source

The ratio of maximum shear stress and average shear stress for a rectangular section is

Answer: 1.5

Rectangular section: tau_max = 3V/2A = 1.5 x tau_avg; key unchanged.

Source 1

Question 6: answer and source

A fixed beam of span L carries a central point load W. The maximum sagging bending moment in the beam is

Answer: WL/8

Fixed-fixed beam with central point load: WL/8 hogging at each support and WL/8 sagging under the load. Legacy key 'WL/4' is the simply supported value and was wrong.

Source 1

Question 7: answer and source

Air entrainment in the concrete increases

Answer: workability

Air entrainment improves workability (and freeze-thaw durability); compressive strength falls with entrained air. Legacy key 'strength' was wrong.

Source 1

Question 8: answer and source

The relation between modulus of rupture Fcr and characteristic strength of concrete Fck is given by

Answer: Fcr = 0.7 S Fck

IS 456 gives fcr = 0.7 x sqrt(fck) (the 'S' in the options stands for the square root). Legacy key '0.35 S Fck' was wrong.

Source 1

Question 9: answer and source

The compressive strength of 100 mm cube as compared to 150 mm cube is always

Answer: more

Smaller cubes test stronger: platen restraint confines the whole 100 mm cube, so it gives higher results than a 150 mm cube. Legacy key 'equal' was wrong.

Source 1

Question 10: answer and source

For a slab supported on its four edges with corners held down and loaded uniformly, the Marcus correction factor to the moments obtained by Grashoff Rankine's theory

Answer: is always less than 1

Marcus's correction reduces the Grashof-Rankine moments, so the factor is always less than 1. Legacy key 'greater than 1' was wrong.

Source 1

Question 11: answer and source

For bars in tension a standard hook has an anchorage value equivalent to a straight length of

Answer: 16

A standard hook is counted as 16 bar diameters of anchorage (16d). Option text clarified ('strength length' to 'straight length'); key unchanged.

Source 1

Question 12: answer and source

Cube strength of controlled concrete to be used for pre-tensioned and post-tensioned work respectively should not be less than

Answer: 420 Kg/cm^2 and 350 Kg/cm^2

Pre-tensioned work requires the higher grade: about 420 kg/cm^2 (42 MPa) for pre-tensioning and 350 kg/cm^2 (35 MPa) for post-tensioning. Legacy key '420 and 530' was wrong.

Source 1

Question 13: answer and source

The creep strains are

Answer: caused due to dead loads only

Creep develops under sustained (permanent) load, i.e. dead load; keyed answer confirmed against the BPSC AE 2019 official paper. Key unchanged.

Source 1

Question 14: answer and source

Ratio of compressive strength to tensile strength of concrete

Answer: increases with age

Tensile strength gains proportionally slower than compressive strength with age, so the ratio increases; key unchanged.

Source 1

Question 15: answer and source

In limit state design of concrete for flexure, the area of stress block is taken as

Answer: 0.36 Fck Xu

IS 456 stress block: resultant compressive force = 0.36 fck.xu per unit width; key unchanged.

Source 1

Question 16: answer and source

The fineness modulus of the fine aggregate is in the range of

Answer: 2.0 to 3.5

Fine aggregates run an FM of roughly 2-4 (commonly quoted 2.0-3.5 for sand). Stem typo corrected ('fitness' to 'fineness'); key unchanged.

Source 1

Question 17: answer and source

According to IS:456, the maximum reinforcement in a column is

Answer: 6%

IS 456 clause 26.5.3.1 caps column longitudinal reinforcement at 6% of the cross-section; key unchanged.

Source 1

Question 18: answer and source

The minimum cover in a slab should neither be less than the diameter of bar nor less than

Answer: 15 mm

IS 456 nominal cover: not less than the bar diameter and not less than 15 mm; key unchanged.

Source 1

Question 19: answer and source

If the permissible stress in steel in tension is 140 N/mm^2, permissible stress in concrete in bending compression is 5 N/mm^2. Then the depth of neutral axis for a singly reinforced rectangular balanced section will be

Answer: 0.40 d

m = 280/(3 x 5) = 18.67; k = m.cbc/(st + m.cbc) = 93.3/233.3 = 0.40, so the neutral axis is at 0.40d; key unchanged.

Source 1

Question 20: answer and source

The slab is designed as one way if the ratio of long span to short span is

Answer: greater than 2

ly/lx greater than 2 makes a slab one-way (IS 456 Annex D); key unchanged.

Source 1

Question 21: answer and source

In any beam when the moment of inertia about the neutral axis is doubled, its deflection is

Answer: halved

Deflection is inversely proportional to EI, so doubling I halves the deflection; key unchanged.

Source 1

Question 22: answer and source

The limits of percentage of the longitudinal reinforcement in a column is given by

Answer: 0.8% to 6%

IS 456 clause 26.5.3.1: not less than 0.8% and not more than 6%; key unchanged.

Source 1

Question 23: answer and source

A rigid prop provided for a beam

Answer: brings the deflection at the prop to zero

A rigid support prevents vertical movement at its section; key unchanged.

Source 1

Question 24: answer and source

In a simply supported beam AB with a concentrated load W at a distance 'a' from support A and 'b' from support B, the deflection under the load is

Answer: Wa^2 b^2 / 3EIL

Standard result: deflection under an eccentric point load = W a^2 b^2 / (3EIL); key unchanged.

Source 1

Question 25: answer and source

For the design of retaining walls the minimum factor of safety against over-turning is taken as

Answer: 2.5

FoS against overturning is at least 2.0 (sliding is 1.5); key unchanged.

Source 1

Question 26: answer and source

A cantilever beam is loaded by a point load at the free end. It is likely to fail by B.M.

Answer: at support

The bending moment in a cantilever is maximum at the fixed support; key unchanged.

Source 1

Question 27: answer and source

The distance between centre lines of a broad gauge is 1.686m. The most economic length of sleeper for efficient distribution of B.M. is

Answer: 2.866 m

The sleeper extends about 0.59 m beyond each rail centre (c/c + 1.18 m = 1.686 + 1.18 = 2.866 m); key unchanged.

Source 1

Question 28: answer and source

In a simply supported beam of span L carrying an eccentric couple M acting at a distance A from the left support, the reaction induced at the support is

Answer: M/L

A pure couple is balanced by an equal and opposite couple M/L x L, so each support reaction is M/L; stem typo corrected ('included' to 'induced'); key unchanged.

Source 1

Question 29: answer and source

The section modulus of square section of side A is

Answer: a^3/6

Z = I/ymax = (a^4/12)/(a/2) = a^3/6; key unchanged.

Source 1

Question 30: answer and source

The minimum percentage of mild steel reinforcement in walls of RCC water tanks of 450 mm thick is about

Answer: 0.20

IS 3370 minimum reinforcement tapers from 0.3% at 100 mm thickness to 0.2% at 450 mm thickness; key unchanged.

Source 1

Change log: 17 November 2026

Original question numbers and review decisions
  • Original Q1: corrected. For a simply supported beam with a central point load, deflection is maximum at mid-span. Stem variable 'I' corrected to 'l' (length); key unchanged.
  • Original Q2: verified as keyed. At constant depth, bending stress fixes b proportional to the bending moment M; key unchanged.
  • Original Q3: corrected. The deflection is the sagitta of the arc: s = l^2/8R (small-deflection approximation). Legacy stem was garbled ('deflects into a uniform strength... width proportional to') and option D 'l^2/2d' corrected to 'l^2/2R'; question repaired to the intended geometry.
  • Original Q4: verified as keyed. Thin cylinder: hoop stress = Pd/2t, longitudinal stress = Pd/4t; key unchanged.
  • Original Q5: verified as keyed. Rectangular section: tau_max = 3V/2A = 1.5 x tau_avg; key unchanged.
  • Original Q6: corrected. Fixed-fixed beam with central point load: WL/8 hogging at each support and WL/8 sagging under the load. Legacy key 'WL/4' is the simply supported value and was wrong.
  • Original Q7: corrected. Air entrainment improves workability (and freeze-thaw durability); compressive strength falls with entrained air. Legacy key 'strength' was wrong.
  • Original Q8: corrected. IS 456 gives fcr = 0.7 x sqrt(fck) (the 'S' in the options stands for the square root). Legacy key '0.35 S Fck' was wrong.
  • Original Q9: corrected. Smaller cubes test stronger: platen restraint confines the whole 100 mm cube, so it gives higher results than a 150 mm cube. Legacy key 'equal' was wrong.
  • Original Q10: corrected. Marcus's correction reduces the Grashof-Rankine moments, so the factor is always less than 1. Legacy key 'greater than 1' was wrong.
  • Original Q11: corrected. A standard hook is counted as 16 bar diameters of anchorage (16d). Option text clarified ('strength length' to 'straight length'); key unchanged.
  • Original Q12: corrected. Pre-tensioned work requires the higher grade: about 420 kg/cm^2 (42 MPa) for pre-tensioning and 350 kg/cm^2 (35 MPa) for post-tensioning. Legacy key '420 and 530' was wrong.
  • Original Q13: verified as keyed. Creep develops under sustained (permanent) load, i.e. dead load; keyed answer confirmed against the BPSC AE 2019 official paper. Key unchanged.
  • Original Q14: verified as keyed. Tensile strength gains proportionally slower than compressive strength with age, so the ratio increases; key unchanged.
  • Original Q15: verified as keyed. IS 456 stress block: resultant compressive force = 0.36 fck.xu per unit width; key unchanged.
  • Original Q16: corrected. Fine aggregates run an FM of roughly 2-4 (commonly quoted 2.0-3.5 for sand). Stem typo corrected ('fitness' to 'fineness'); key unchanged.
  • Original Q17: verified as keyed. IS 456 clause 26.5.3.1 caps column longitudinal reinforcement at 6% of the cross-section; key unchanged.
  • Original Q18: verified as keyed. IS 456 nominal cover: not less than the bar diameter and not less than 15 mm; key unchanged.
  • Original Q19: verified as keyed. m = 280/(3 x 5) = 18.67; k = m.cbc/(st + m.cbc) = 93.3/233.3 = 0.40, so the neutral axis is at 0.40d; key unchanged.
  • Original Q20: verified as keyed. ly/lx greater than 2 makes a slab one-way (IS 456 Annex D); key unchanged.
  • Original Q21: verified as keyed. Deflection is inversely proportional to EI, so doubling I halves the deflection; key unchanged.
  • Original Q22: verified as keyed. IS 456 clause 26.5.3.1: not less than 0.8% and not more than 6%; key unchanged.
  • Original Q23: verified as keyed. A rigid support prevents vertical movement at its section; key unchanged.
  • Original Q24: verified as keyed. Standard result: deflection under an eccentric point load = W a^2 b^2 / (3EIL); key unchanged.
  • Original Q25: verified as keyed. FoS against overturning is at least 2.0 (sliding is 1.5); key unchanged.
  • Original Q26: verified as keyed. The bending moment in a cantilever is maximum at the fixed support; key unchanged.
  • Original Q27: verified as keyed. The sleeper extends about 0.59 m beyond each rail centre (c/c + 1.18 m = 1.686 + 1.18 = 2.866 m); key unchanged.
  • Original Q28: corrected. A pure couple is balanced by an equal and opposite couple M/L x L, so each support reaction is M/L; stem typo corrected ('included' to 'induced'); key unchanged.
  • Original Q30: verified as keyed. Z = I/ymax = (a^4/12)/(a/2) = a^3/6; key unchanged.
  • Original Q31: verified as keyed. IS 3370 minimum reinforcement tapers from 0.3% at 100 mm thickness to 0.2% at 450 mm thickness; key unchanged.
  • Original Q29: Stem lost its beam data in the legacy file (no loading given), so no option, including the keyed 140 KNm, can be verified or computed. Dropped as unfixable.