第 2 级


31 reviewed questions. Choose answers, then Calculate. Clear resets all selections. Unanswered questions score zero and remain in the percentage denominator. Open the answer review below for sources.

请输入数值:
结果:
%

Answers and sources

Reviewed 17 November 2026. Ambiguous, malformed and unverified legacy questions have been removed. Wording and answer choices have been corrected where needed. This is a study quiz, not certification of engineering or laboratory decisions.

Question 1: answer and source

Work done in a free expansion process is

Answer: Zero

In free (Joule) expansion the gas pushes against no external pressure, so no work is done; key unchanged.

Source 1

Question 2: answer and source

A system absorbs 100 kJ of heat and the increase in its internal energy is 100 kJ; the work done is

Answer: 0 kJ

First law: W = Q - dU = 100 - 100 = 0 kJ; key unchanged.

Source 1

Question 3: answer and source

The specific heats of a gas at constant pressure and constant volume are respectively 1.0 kJ/kg K and 0.72 kJ/kg K; the value of R for the gas is

Answer: 0.28 kJ/kg K

Mayer's relation: R = cp - cv = 1.0 - 0.72 = 0.28 kJ/kg K. Legacy option '0.272 kJ/kg K' corrected to the computed 0.28.

Source 1

Question 4: answer and source

The compression ratio for a petrol engine generally lies between

Answer: 6 and 10

SI (petrol) engines typically run compression ratios of 6:1 to 10:1; 14-22 is the diesel (CI) range. Legacy key '10 and 14' was wrong.

Source 1

Question 5: answer and source

The SFC of an engine is 0.25 kg/kW hr when the fuel used has a calorific value of 36000 kJ/kg. The thermal efficiency of the engine is

Answer: 40%

Efficiency = 3600 / (SFC x CV) = 3600 / (0.25 x 36000) = 40%; key unchanged.

Source 1

Question 6: answer and source

When steam condenses and becomes water at the same temperature, the specific heat for the process in kJ/kg K is

Answer: infinity

During an isothermal phase change c = Q/(m.dT) with dT = 0, so the specific heat is infinite (heat moves as latent heat only). Legacy key '1.0' was wrong.

Source 1

Question 7: answer and source

In a vapour absorption refrigeration machine the fluids used are

Answer: water and ammonia

The classic absorption pair is ammonia (refrigerant) with water (absorbent); key unchanged.

Source 1

Question 8: answer and source

In a Carnot engine with an efficiency of 40%, the heat rejected to the sink at 27 C is 60 kJ. The heat supplied in kJ to the engine by the source is

Answer: 100

Qs = Qr / (1 - eta) = 60 / 0.6 = 100 kJ; key unchanged.

Source 1

Question 9: answer and source

In a simple spur gear train, gears with 24, 48, 32, 72 and 96 teeth are in sequence. The gear with 24 teeth runs at 900 rpm. The speed in rpm of the gear with 72 teeth is

Answer: 300

Intermediate gears are idlers: speed ratio accumulates to 24/72, so 900 x 24/72 = 300 rpm; key unchanged.

Source 1

Question 10: answer and source

A governor in an IC engine controls the

Answer: load fluctuations

A governor adjusts fuel supply to hold speed against load fluctuations (a flywheel handles cyclic variation). Typos corrected ('governer', 'Ic'); key unchanged.

Source 1

Question 11: answer and source

For a spring controlled governor the relation F = ar + b (F is the controlling force, r is the radius of rotation, a and b are constants), indicates that the governor is

Answer: unstable

Stability needs dF/dr > F/r; with F = ar + b and b positive, dF/dr = a < a + b/r = F/r, so the governor is unstable. Option typo corrected ('insochronous'); key unchanged.

Source 1

Question 12: answer and source

1.25 kg of hydrogen are burnt with stoichiometric air; the mass of air in kg required is (choose the nearest value)

Answer: 43.5

Stoichiometric air for hydrogen is about 34.3 kg per kg, so 1.25 kg needs about 43 kg of air; 43.5 is the nearest option. Stem typo corrected ('stiochiometric'); key unchanged.

Source 1

Question 13: answer and source

A low wet bulb temperature indicates

Answer: cool air with low specific humidity

The drier the air, the faster water evaporates and the lower the wet-bulb reading, so a low wet bulb temperature means low specific humidity. Legacy key 'high specific humidity' was wrong.

Source 1

Question 14: answer and source

The moisture in air will condense at

Answer: dew point temperature

Water vapour condenses when air is cooled to its dew point. Option corrected (was 'low point temperature', a typo of 'dew point'); key unchanged.

Source 1

Question 15: answer and source

The air refrigeration cycle works on the

Answer: Bell Coleman cycle

Air refrigeration runs on the Bell-Coleman (reversed Brayton) cycle. Option spelling corrected ('Sterling'); key unchanged.

Source 1

Question 16: answer and source

A feather key is one of the following types

Answer: sunk

Feather keys are a type of sunk key. Stem clarified ('is on one the' to 'is one of the'); key unchanged.

Source 1

Question 17: answer and source

A cotter joint is generally used to transmit

Answer: tensile forces

A cotter joint connects two co-axial rods under axial tensile (or compressive) load; it is not a shaft/torque joint. Legacy key 'shear forces' was wrong.

Source 1

Question 18: answer and source

The screw thread commonly used for transmission of motion is one of the following types of threads

Answer: acme

Acme/trapezoidal threads are used for motion transmission (lead screws); V-threads are for fastening. Key unchanged.

Source 1

Question 19: answer and source

In a flange coupling, the flange bolts are designed for

Answer: shear forces

Coupling bolts transmit torque in shear (checked for shear and bearing stresses); key unchanged.

Source 1

Question 20: answer and source

In power transmission using open belts on horizontal shafts it is preferable to have the slack side of the belt on the top because

Answer: the angle of contact is more

A sagging slack side on top increases the angle of wrap, which increases power capacity; key unchanged.

Source 1

Question 21: answer and source

Centrifugal tension in belts results in

Answer: reduced power transmission

Centrifugal tension lifts the belt off the pulley and reduces the effective tension difference, so transmitted power drops; key unchanged.

Source 1

Question 22: answer and source

One of the following materials is commonly used for bearings

Answer: gun metal

Gun metal (a bronze) is a standard bearing material. Typo corrected ('comonly'); key unchanged.

Source 1

Question 23: answer and source

Babbitt metal is an alloy of

Answer: tin, copper, antimony and lead

Babbitt bearing alloys are tin/lead-based with antimony and copper; key unchanged.

Source 1

Question 24: answer and source

A mass of 40 kg is about to slide down when placed on a plane inclined at 30 degrees to the horizontal. The coefficient of friction between the plane and the mass is

Answer: 1/sqrt(3) (= tan 30 deg, about 0.577)

At impending slip mu = tan(theta) = tan 30 deg = 1/sqrt(3) = 0.577. Legacy option '1/3' corrected to 1/sqrt(3) and re-keyed; the mass is irrelevant.

Source 1

Question 25: answer and source

Two forces of magnitude 30 N and 40 N act at right angles at a point; the magnitude of the resultant force is

Answer: 50 N

Resultant = sqrt(30^2 + 40^2) = 50 N; key unchanged.

Source 1

Question 26: answer and source

A simply supported beam has a uniformly distributed load on it; the bending moment diagram is

Answer: parabola

For a UDL on a simply supported beam the bending moment diagram is a parabola; key unchanged.

Source 1

Question 27: answer and source

A 3 m long simply supported beam has a load of 60 N acting at a distance of 1 m from the left hand support; the shear force at a distance of 1 m from the right hand support is

Answer: 20 N

Right reaction = 60 x 1/3 = 20 N; just left of the right support the shear force magnitude is 20 N (option '20 Nm' has a wrong unit). Key unchanged.

Source 1

Question 28: answer and source

A box of 10 kg mass is being pulled to the left by a force of 10 N and to the right by a force of 15 N, both forces acting parallel to each other. The acceleration of the box in m/s^2 is

Answer: 0.5

Net force = 15 - 10 = 5 N, so a = F/m = 5/10 = 0.5 m/s^2; key unchanged.

Source 1

Question 29: answer and source

An object moves on a horizontal plane at a velocity of 1 m/sec. If no external force acts on the object, its velocity after 5 sec is

Answer: 1 m/s

With no external force the velocity stays unchanged (Newton's first law): 1 m/s. Typo corrected ('ont'); key unchanged.

Source 1

Question 30: answer and source

A square block weighing 30 N rests on the ground, the coefficient of friction between the block and the ground is 0.6. The force required to pull the block horizontally is

Answer: 18 N

Limiting friction = mu x N = 0.6 x 30 = 18 N. Typo corrected ('wieghtining'); key unchanged.

Source 1

Question 31: answer and source

A military organisation is known as

Answer: Line organisation

Line organisation is also called the military or scalar organisation; key unchanged.

Source 1

Change log: 17 November 2026

Original question numbers and review decisions
  • Original Q1: verified as keyed. In free (Joule) expansion the gas pushes against no external pressure, so no work is done; key unchanged.
  • Original Q2: verified as keyed. First law: W = Q - dU = 100 - 100 = 0 kJ; key unchanged.
  • Original Q3: corrected. Mayer's relation: R = cp - cv = 1.0 - 0.72 = 0.28 kJ/kg K. Legacy option '0.272 kJ/kg K' corrected to the computed 0.28.
  • Original Q4: corrected. SI (petrol) engines typically run compression ratios of 6:1 to 10:1; 14-22 is the diesel (CI) range. Legacy key '10 and 14' was wrong.
  • Original Q5: verified as keyed. Efficiency = 3600 / (SFC x CV) = 3600 / (0.25 x 36000) = 40%; key unchanged.
  • Original Q6: corrected. During an isothermal phase change c = Q/(m.dT) with dT = 0, so the specific heat is infinite (heat moves as latent heat only). Legacy key '1.0' was wrong.
  • Original Q7: verified as keyed. The classic absorption pair is ammonia (refrigerant) with water (absorbent); key unchanged.
  • Original Q8: verified as keyed. Qs = Qr / (1 - eta) = 60 / 0.6 = 100 kJ; key unchanged.
  • Original Q9: verified as keyed. Intermediate gears are idlers: speed ratio accumulates to 24/72, so 900 x 24/72 = 300 rpm; key unchanged.
  • Original Q10: corrected. A governor adjusts fuel supply to hold speed against load fluctuations (a flywheel handles cyclic variation). Typos corrected ('governer', 'Ic'); key unchanged.
  • Original Q11: corrected. Stability needs dF/dr > F/r; with F = ar + b and b positive, dF/dr = a < a + b/r = F/r, so the governor is unstable. Option typo corrected ('insochronous'); key unchanged.
  • Original Q12: corrected. Stoichiometric air for hydrogen is about 34.3 kg per kg, so 1.25 kg needs about 43 kg of air; 43.5 is the nearest option. Stem typo corrected ('stiochiometric'); key unchanged.
  • Original Q13: corrected. The drier the air, the faster water evaporates and the lower the wet-bulb reading, so a low wet bulb temperature means low specific humidity. Legacy key 'high specific humidity' was wrong.
  • Original Q14: corrected. Water vapour condenses when air is cooled to its dew point. Option corrected (was 'low point temperature', a typo of 'dew point'); key unchanged.
  • Original Q15: corrected. Air refrigeration runs on the Bell-Coleman (reversed Brayton) cycle. Option spelling corrected ('Sterling'); key unchanged.
  • Original Q16: corrected. Feather keys are a type of sunk key. Stem clarified ('is on one the' to 'is one of the'); key unchanged.
  • Original Q17: corrected. A cotter joint connects two co-axial rods under axial tensile (or compressive) load; it is not a shaft/torque joint. Legacy key 'shear forces' was wrong.
  • Original Q18: verified as keyed. Acme/trapezoidal threads are used for motion transmission (lead screws); V-threads are for fastening. Key unchanged.
  • Original Q19: verified as keyed. Coupling bolts transmit torque in shear (checked for shear and bearing stresses); key unchanged.
  • Original Q20: verified as keyed. A sagging slack side on top increases the angle of wrap, which increases power capacity; key unchanged.
  • Original Q21: verified as keyed. Centrifugal tension lifts the belt off the pulley and reduces the effective tension difference, so transmitted power drops; key unchanged.
  • Original Q22: corrected. Gun metal (a bronze) is a standard bearing material. Typo corrected ('comonly'); key unchanged.
  • Original Q23: verified as keyed. Babbitt bearing alloys are tin/lead-based with antimony and copper; key unchanged.
  • Original Q24: corrected. At impending slip mu = tan(theta) = tan 30 deg = 1/sqrt(3) = 0.577. Legacy option '1/3' corrected to 1/sqrt(3) and re-keyed; the mass is irrelevant.
  • Original Q25: verified as keyed. Resultant = sqrt(30^2 + 40^2) = 50 N; key unchanged.
  • Original Q26: verified as keyed. For a UDL on a simply supported beam the bending moment diagram is a parabola; key unchanged.
  • Original Q27: corrected. Right reaction = 60 x 1/3 = 20 N; just left of the right support the shear force magnitude is 20 N (option '20 Nm' has a wrong unit). Key unchanged.
  • Original Q28: verified as keyed. Net force = 15 - 10 = 5 N, so a = F/m = 5/10 = 0.5 m/s^2; key unchanged.
  • Original Q29: corrected. With no external force the velocity stays unchanged (Newton's first law): 1 m/s. Typo corrected ('ont'); key unchanged.
  • Original Q30: corrected. Limiting friction = mu x N = 0.6 x 30 = 18 N. Typo corrected ('wieghtining'); key unchanged.
  • Original Q31: verified as keyed. Line organisation is also called the military or scalar organisation; key unchanged.