المستوى 4


31 reviewed questions. Choose answers, then Calculate. Clear resets all selections. Unanswered questions score zero and remain in the percentage denominator. Open the answer review below for sources.

أدخل القيم:
النتائج:
%

Answers and sources

Reviewed 17 November 2026. Ambiguous, malformed and unverified legacy questions have been removed. Wording and answer choices have been corrected where needed. This is a study quiz, not certification of engineering or laboratory decisions.

Question 1: answer and source

When small castings are to be produced in large numbers, the type of pattern generally used will be

Answer: match plate pattern

Match plate patterns allow high-production machine moulding of small castings; key unchanged.

Question 2: answer and source

Cylindrical bores are measured using

Answer: plug gauges

Bores are checked with plug (limit) gauges; legacy keyed 'cylindrical gauges'.

Question 3: answer and source

The operation of finishing a drilled hole to the correct size is known as

Answer: reaming

Reaming sizes and finishes a drilled hole; key unchanged.

Question 4: answer and source

One of the most important techniques of establishing the standard time of doing a job is through

Answer: time study

Standard time comes from time study; key unchanged.

Question 5: answer and source

Hardened gears are finished by

Answer: gear grinding

Only grinding can finish hardened gear teeth; key unchanged. Fixed misprint 'grindling'.

Question 6: answer and source

The tool life is affected to the maximum extent by

Answer: the cutting speed

Taylor's tool-life equation shows cutting speed dominates tool life; key unchanged.

Question 7: answer and source

The centrifugal tension in belts

Answer: decrease power transmission

Centrifugal tension reduces effective grip and hence power transmission; key unchanged.

Question 8: answer and source

A process in which no heat is supplied or rejected and entropy is constant is known as

Answer: isentropic process

Reversible adiabatic = constant entropy = isentropic; key unchanged. Fixed misprint 'isentroic'.

Question 9: answer and source

Critical pressure ratio for a convergent nozzle is

Answer: the ratio of the pressures at outlet and inlet of nozzle when the mass flow is a maximum

The critical ratio is the throat/inlet pressure ratio at choking (maximum mass flow); key unchanged. The legacy 4th option was empty; replaced with 'None of these'.

Question 10: answer and source

A belt can transmit maximum power when the total tension of the drive is

Answer: three times the centrifugal tension

Maximum power condition: total maximum tension = 3 x centrifugal tension; key unchanged.

Question 11: answer and source

Curtis turbine is a

Answer: velocity-compounded turbine

The Curtis stage compounds velocity (one nozzle row, two blade rows); key unchanged.

Question 12: answer and source

Newton is a unit of

Answer: Force

Newton is the SI unit of force; key unchanged.

Question 13: answer and source

Air fuel ratio in a jet engine is

Answer: 60:1

Jet engines run very lean, about 60:1 overall; key unchanged. Fixed misprint 'fule'.

Question 14: answer and source

Which one of the following is spring loaded type

Answer: Hartnell governor

The Hartnell governor uses a spring instead of dead weights; key unchanged. Fixed misprint 'Hartnel'.

Question 15: answer and source

The part which provides simple harmonic motion to the D-slide valve of a steam engine is called

Answer: eccentric rod

The eccentric (through the eccentric rod) imparts simple harmonic motion to the slide valve; legacy keyed valve rod. Fixed misprint 'valce'.

Question 16: answer and source

The refrigerant used in vapour absorption refrigeration

Answer: Aqua-ammonia

The classic absorption system uses aqua-ammonia (NH3 refrigerant, water absorbent); key unchanged.

Question 17: answer and source

The compression ratio of a petrol engine is approximately

Answer: 7:1

Petrol engines run about 6-8:1 due to knock limits (18-25:1 is diesel); key unchanged.

Question 18: answer and source

The dimensional formula MLT^-2 represents

Answer: force

Force = mass x acceleration = MLT^-2; key unchanged. Fixed formula sign (was MLT^2).

Question 19: answer and source

The function of a carburettor is to supply

Answer: air and petrol

A carburettor meters and mixes petrol with air; key unchanged.

Question 20: answer and source

For cooling the pistons of diesel engine common fluid used is

Answer: lubricating oil

Pistons are commonly oil-cooled (lubricating oil through the crown); key unchanged.

Question 21: answer and source

To produce a spark across the gap of a spark plug, the voltage used is

Answer: 6000 to 10000 volts

Classic ignition systems deliver 6,000-10,000 V to jump the plug gap; key unchanged.

Question 22: answer and source

For the steam which is initially saturated and flowing through a nozzle, the ratio of pressures at exit and inlet for maximum discharge is equal to

Answer: 0.582

With n = 1.135 for initially saturated steam, critical ratio = (2/(n+1))^(n/(n-1)) = 0.582; key unchanged. Fixed misprint 'andflowing'.

Question 23: answer and source

A stone of mass 1 kg tied to a string of 1 metre long is rotated in a horizontal circle at a constant angular speed of 5 rad/sec, then the tension in the string will be

Answer: 25N

T = m w^2 r = 1 x 25 x 1 = 25 N; key unchanged.

Question 24: answer and source

A lift descends with an acceleration of 0.5 metres/sec^2 from the top floor of a multistoried building. The time required to travel a distance of 25 metres will be

Answer: 10 sec

s = (1/2) a t^2 gives t = sqrt(2 x 25 / 0.5) = 10 s; key unchanged.

Question 25: answer and source

The coefficient of Performance for a refrigerator will be

Answer: above 1.0

Refrigerator COP is typically 2-6, above 1; key unchanged.

Question 26: answer and source

If the acceleration due to gravity is doubled at any place, the weight of the body will be

Answer: double

W = mg, so doubling g doubles the weight; key unchanged.

Question 27: answer and source

The internal energy of a gas is a

Answer: function of temperature only

For an ideal gas internal energy depends on temperature alone; key unchanged.

Question 28: answer and source

The unit of power is SI unit is

Answer: Watt

SI unit of power is the watt; key unchanged.

Question 29: answer and source

In a flow through nozzle, the steam undergoes

Answer: adiabatic process

Nozzle flow is rapid with negligible heat transfer: (approximately) adiabatic expansion; legacy keyed constant volume.

Question 30: answer and source

Welding defect called Arc blow occurs in

Answer: Arc welding using DC current

Arc blow is magnetic deflection of the arc, encountered in DC arc welding; legacy keyed MIG welding.

Question 31: answer and source

Draft on a pattern is provided for

Answer: facilitating withdrawal of the pattern from the mould

Draft (taper) lets the pattern be withdrawn without damaging the mould; shrinkage is handled by shrinkage allowance; legacy keyed shrinkage. Fixed misprint 'strinkage'.

Change log: 17 November 2026

Original question numbers and review decisions
  • Original Q1: verified as keyed. Match plate patterns allow high-production machine moulding of small castings; key unchanged.
  • Original Q2: verified as keyed. Bores are checked with plug (limit) gauges; legacy keyed 'cylindrical gauges'.
  • Original Q3: verified as keyed. Reaming sizes and finishes a drilled hole; key unchanged.
  • Original Q4: verified as keyed. Standard time comes from time study; key unchanged.
  • Original Q5: verified as keyed. Only grinding can finish hardened gear teeth; key unchanged. Fixed misprint 'grindling'.
  • Original Q6: verified as keyed. Taylor's tool-life equation shows cutting speed dominates tool life; key unchanged.
  • Original Q7: verified as keyed. Centrifugal tension reduces effective grip and hence power transmission; key unchanged.
  • Original Q8: verified as keyed. Reversible adiabatic = constant entropy = isentropic; key unchanged. Fixed misprint 'isentroic'.
  • Original Q9: verified as keyed. The critical ratio is the throat/inlet pressure ratio at choking (maximum mass flow); key unchanged. The legacy 4th option was empty; replaced with 'None of these'.
  • Original Q10: verified as keyed. Maximum power condition: total maximum tension = 3 x centrifugal tension; key unchanged.
  • Original Q11: verified as keyed. The Curtis stage compounds velocity (one nozzle row, two blade rows); key unchanged.
  • Original Q12: verified as keyed. Newton is the SI unit of force; key unchanged.
  • Original Q13: verified as keyed. Jet engines run very lean, about 60:1 overall; key unchanged. Fixed misprint 'fule'.
  • Original Q14: verified as keyed. The Hartnell governor uses a spring instead of dead weights; key unchanged. Fixed misprint 'Hartnel'.
  • Original Q15: verified as keyed. The eccentric (through the eccentric rod) imparts simple harmonic motion to the slide valve; legacy keyed valve rod. Fixed misprint 'valce'.
  • Original Q16: verified as keyed. The classic absorption system uses aqua-ammonia (NH3 refrigerant, water absorbent); key unchanged.
  • Original Q17: verified as keyed. Petrol engines run about 6-8:1 due to knock limits (18-25:1 is diesel); key unchanged.
  • Original Q18: verified as keyed. Force = mass x acceleration = MLT^-2; key unchanged. Fixed formula sign (was MLT^2).
  • Original Q19: verified as keyed. A carburettor meters and mixes petrol with air; key unchanged.
  • Original Q20: verified as keyed. Pistons are commonly oil-cooled (lubricating oil through the crown); key unchanged.
  • Original Q21: verified as keyed. Classic ignition systems deliver 6,000-10,000 V to jump the plug gap; key unchanged.
  • Original Q22: verified as keyed. With n = 1.135 for initially saturated steam, critical ratio = (2/(n+1))^(n/(n-1)) = 0.582; key unchanged. Fixed misprint 'andflowing'.
  • Original Q23: verified as keyed. T = m w^2 r = 1 x 25 x 1 = 25 N; key unchanged.
  • Original Q24: verified as keyed. s = (1/2) a t^2 gives t = sqrt(2 x 25 / 0.5) = 10 s; key unchanged.
  • Original Q25: verified as keyed. Refrigerator COP is typically 2-6, above 1; key unchanged.
  • Original Q26: verified as keyed. W = mg, so doubling g doubles the weight; key unchanged.
  • Original Q27: verified as keyed. For an ideal gas internal energy depends on temperature alone; key unchanged.
  • Original Q28: verified as keyed. SI unit of power is the watt; key unchanged.
  • Original Q29: verified as keyed. Nozzle flow is rapid with negligible heat transfer: (approximately) adiabatic expansion; legacy keyed constant volume.
  • Original Q30: verified as keyed. Arc blow is magnetic deflection of the arc, encountered in DC arc welding; legacy keyed MIG welding.
  • Original Q31: verified as keyed. Draft (taper) lets the pattern be withdrawn without damaging the mould; shrinkage is handled by shrinkage allowance; legacy keyed shrinkage. Fixed misprint 'strinkage'.