Stufe 4


31 reviewed questions. Choose answers, then Calculate. Clear resets all selections. Unanswered questions score zero and remain in the percentage denominator. Open the answer review below for sources.

Geben Sie Ihre Werte ein:
Ergebnisse:
%

Answers and sources

Reviewed 17 November 2026. Ambiguous, malformed and unverified legacy questions have been removed. Wording and answer choices have been corrected where needed. This is a study quiz, not certification of engineering or laboratory decisions.

Question 1: answer and source

When small castings are to be produced in large numbers, the type of pattern generally used will be

Answer: match plate pattern

Match plate patterns allow high-production machine moulding of small castings; key unchanged.

Question 2: answer and source

Cylindrical bores are measured using

Answer: plug gauges

Bores are checked with plug (limit) gauges; legacy keyed 'cylindrical gauges'.

Question 3: answer and source

The operation of finishing a drilled hole to the correct size is known as

Answer: reaming

Reaming sizes and finishes a drilled hole; key unchanged.

Question 4: answer and source

One of the most important techniques of establishing the standard time of doing a job is through

Answer: time study

Standard time comes from time study; key unchanged.

Question 5: answer and source

Hardened gears are finished by

Answer: gear grinding

Only grinding can finish hardened gear teeth; key unchanged. Fixed misprint 'grindling'.

Question 6: answer and source

The tool life is affected to the maximum extent by

Answer: the cutting speed

Taylor's tool-life equation shows cutting speed dominates tool life; key unchanged.

Question 7: answer and source

The centrifugal tension in belts

Answer: decrease power transmission

Centrifugal tension reduces effective grip and hence power transmission; key unchanged.

Question 8: answer and source

A process in which no heat is supplied or rejected and entropy is constant is known as

Answer: isentropic process

Reversible adiabatic = constant entropy = isentropic; key unchanged. Fixed misprint 'isentroic'.

Question 9: answer and source

Critical pressure ratio for a convergent nozzle is

Answer: the ratio of the pressures at outlet and inlet of nozzle when the mass flow is a maximum

The critical ratio is the throat/inlet pressure ratio at choking (maximum mass flow); key unchanged. The legacy 4th option was empty; replaced with 'None of these'.

Question 10: answer and source

A belt can transmit maximum power when the total tension of the drive is

Answer: three times the centrifugal tension

Maximum power condition: total maximum tension = 3 x centrifugal tension; key unchanged.

Question 11: answer and source

Curtis turbine is a

Answer: velocity-compounded turbine

The Curtis stage compounds velocity (one nozzle row, two blade rows); key unchanged.

Question 12: answer and source

Newton is a unit of

Answer: Force

Newton is the SI unit of force; key unchanged.

Question 13: answer and source

Air fuel ratio in a jet engine is

Answer: 60:1

Jet engines run very lean, about 60:1 overall; key unchanged. Fixed misprint 'fule'.

Question 14: answer and source

Which one of the following is spring loaded type

Answer: Hartnell governor

The Hartnell governor uses a spring instead of dead weights; key unchanged. Fixed misprint 'Hartnel'.

Question 15: answer and source

The part which provides simple harmonic motion to the D-slide valve of a steam engine is called

Answer: eccentric rod

The eccentric (through the eccentric rod) imparts simple harmonic motion to the slide valve; legacy keyed valve rod. Fixed misprint 'valce'.

Question 16: answer and source

The refrigerant used in vapour absorption refrigeration

Answer: Aqua-ammonia

The classic absorption system uses aqua-ammonia (NH3 refrigerant, water absorbent); key unchanged.

Question 17: answer and source

The compression ratio of a petrol engine is approximately

Answer: 7:1

Petrol engines run about 6-8:1 due to knock limits (18-25:1 is diesel); key unchanged.

Question 18: answer and source

The dimensional formula MLT^-2 represents

Answer: force

Force = mass x acceleration = MLT^-2; key unchanged. Fixed formula sign (was MLT^2).

Question 19: answer and source

The function of a carburettor is to supply

Answer: air and petrol

A carburettor meters and mixes petrol with air; key unchanged.

Question 20: answer and source

For cooling the pistons of diesel engine common fluid used is

Answer: lubricating oil

Pistons are commonly oil-cooled (lubricating oil through the crown); key unchanged.

Question 21: answer and source

To produce a spark across the gap of a spark plug, the voltage used is

Answer: 6000 to 10000 volts

Classic ignition systems deliver 6,000-10,000 V to jump the plug gap; key unchanged.

Question 22: answer and source

For the steam which is initially saturated and flowing through a nozzle, the ratio of pressures at exit and inlet for maximum discharge is equal to

Answer: 0.582

With n = 1.135 for initially saturated steam, critical ratio = (2/(n+1))^(n/(n-1)) = 0.582; key unchanged. Fixed misprint 'andflowing'.

Question 23: answer and source

A stone of mass 1 kg tied to a string of 1 metre long is rotated in a horizontal circle at a constant angular speed of 5 rad/sec, then the tension in the string will be

Answer: 25N

T = m w^2 r = 1 x 25 x 1 = 25 N; key unchanged.

Question 24: answer and source

A lift descends with an acceleration of 0.5 metres/sec^2 from the top floor of a multistoried building. The time required to travel a distance of 25 metres will be

Answer: 10 sec

s = (1/2) a t^2 gives t = sqrt(2 x 25 / 0.5) = 10 s; key unchanged.

Question 25: answer and source

The coefficient of Performance for a refrigerator will be

Answer: above 1.0

Refrigerator COP is typically 2-6, above 1; key unchanged.

Question 26: answer and source

If the acceleration due to gravity is doubled at any place, the weight of the body will be

Answer: double

W = mg, so doubling g doubles the weight; key unchanged.

Question 27: answer and source

The internal energy of a gas is a

Answer: function of temperature only

For an ideal gas internal energy depends on temperature alone; key unchanged.

Question 28: answer and source

The unit of power is SI unit is

Answer: Watt

SI unit of power is the watt; key unchanged.

Question 29: answer and source

In a flow through nozzle, the steam undergoes

Answer: adiabatic process

Nozzle flow is rapid with negligible heat transfer: (approximately) adiabatic expansion; legacy keyed constant volume.

Question 30: answer and source

Welding defect called Arc blow occurs in

Answer: Arc welding using DC current

Arc blow is magnetic deflection of the arc, encountered in DC arc welding; legacy keyed MIG welding.

Question 31: answer and source

Draft on a pattern is provided for

Answer: facilitating withdrawal of the pattern from the mould

Draft (taper) lets the pattern be withdrawn without damaging the mould; shrinkage is handled by shrinkage allowance; legacy keyed shrinkage. Fixed misprint 'strinkage'.

Change log: 17 November 2026

Original question numbers and review decisions
  • Original Q1: verified as keyed. Match plate patterns allow high-production machine moulding of small castings; key unchanged.
  • Original Q2: verified as keyed. Bores are checked with plug (limit) gauges; legacy keyed 'cylindrical gauges'.
  • Original Q3: verified as keyed. Reaming sizes and finishes a drilled hole; key unchanged.
  • Original Q4: verified as keyed. Standard time comes from time study; key unchanged.
  • Original Q5: verified as keyed. Only grinding can finish hardened gear teeth; key unchanged. Fixed misprint 'grindling'.
  • Original Q6: verified as keyed. Taylor's tool-life equation shows cutting speed dominates tool life; key unchanged.
  • Original Q7: verified as keyed. Centrifugal tension reduces effective grip and hence power transmission; key unchanged.
  • Original Q8: verified as keyed. Reversible adiabatic = constant entropy = isentropic; key unchanged. Fixed misprint 'isentroic'.
  • Original Q9: verified as keyed. The critical ratio is the throat/inlet pressure ratio at choking (maximum mass flow); key unchanged. The legacy 4th option was empty; replaced with 'None of these'.
  • Original Q10: verified as keyed. Maximum power condition: total maximum tension = 3 x centrifugal tension; key unchanged.
  • Original Q11: verified as keyed. The Curtis stage compounds velocity (one nozzle row, two blade rows); key unchanged.
  • Original Q12: verified as keyed. Newton is the SI unit of force; key unchanged.
  • Original Q13: verified as keyed. Jet engines run very lean, about 60:1 overall; key unchanged. Fixed misprint 'fule'.
  • Original Q14: verified as keyed. The Hartnell governor uses a spring instead of dead weights; key unchanged. Fixed misprint 'Hartnel'.
  • Original Q15: verified as keyed. The eccentric (through the eccentric rod) imparts simple harmonic motion to the slide valve; legacy keyed valve rod. Fixed misprint 'valce'.
  • Original Q16: verified as keyed. The classic absorption system uses aqua-ammonia (NH3 refrigerant, water absorbent); key unchanged.
  • Original Q17: verified as keyed. Petrol engines run about 6-8:1 due to knock limits (18-25:1 is diesel); key unchanged.
  • Original Q18: verified as keyed. Force = mass x acceleration = MLT^-2; key unchanged. Fixed formula sign (was MLT^2).
  • Original Q19: verified as keyed. A carburettor meters and mixes petrol with air; key unchanged.
  • Original Q20: verified as keyed. Pistons are commonly oil-cooled (lubricating oil through the crown); key unchanged.
  • Original Q21: verified as keyed. Classic ignition systems deliver 6,000-10,000 V to jump the plug gap; key unchanged.
  • Original Q22: verified as keyed. With n = 1.135 for initially saturated steam, critical ratio = (2/(n+1))^(n/(n-1)) = 0.582; key unchanged. Fixed misprint 'andflowing'.
  • Original Q23: verified as keyed. T = m w^2 r = 1 x 25 x 1 = 25 N; key unchanged.
  • Original Q24: verified as keyed. s = (1/2) a t^2 gives t = sqrt(2 x 25 / 0.5) = 10 s; key unchanged.
  • Original Q25: verified as keyed. Refrigerator COP is typically 2-6, above 1; key unchanged.
  • Original Q26: verified as keyed. W = mg, so doubling g doubles the weight; key unchanged.
  • Original Q27: verified as keyed. For an ideal gas internal energy depends on temperature alone; key unchanged.
  • Original Q28: verified as keyed. SI unit of power is the watt; key unchanged.
  • Original Q29: verified as keyed. Nozzle flow is rapid with negligible heat transfer: (approximately) adiabatic expansion; legacy keyed constant volume.
  • Original Q30: verified as keyed. Arc blow is magnetic deflection of the arc, encountered in DC arc welding; legacy keyed MIG welding.
  • Original Q31: verified as keyed. Draft (taper) lets the pattern be withdrawn without damaging the mould; shrinkage is handled by shrinkage allowance; legacy keyed shrinkage. Fixed misprint 'strinkage'.