Уровень 3
30 reviewed questions. Choose answers, then Calculate. Clear resets all selections. Unanswered questions score zero and remain in the percentage denominator. Open the answer review below for sources.
Answers and sources
Reviewed 17 November 2026. Ambiguous, malformed and unverified legacy questions have been removed. Wording and answer choices have been corrected where needed. This is a study quiz, not certification of engineering or laboratory decisions.
Question 1: answer and source
According to Unwin's formula, if t is thickness of the plate in mm, the nominal diameter of the rivet is
Answer: d = 6.05 Sqrt(t)
Post-publish correction 2026-11-17: Unwin formula is d = 6.05 x sqrt(t) mm (French formula d = 1.5t + 4). Legacy options contained only 1.91-family values (misprint); replaced the option set and keyed 6.05 sqrt(t).
Question 2: answer and source
The slenderness ratio of a column is zero when its length
Answer: is supported on all sides throughout its length
When the member is supported all along, its effective buckling length is zero, so the slenderness ratio is zero. Legacy key 'between the points of zero moments' was wrong.
Question 3: answer and source
According to IS 800, lacing bars resist transverse shear equal to
Answer: 2.5% of the axial load
IS 800 designs lacings for a transverse shear of 2.5% of the axial force in the member; stem punctuation cleaned; key unchanged.
Question 4: answer and source
When the length of tension member is too long
Answer: a wire is used
Very long tension members (e.g. suspension cables) use wires/wire ropes. Legacy key 'a bar is used' was wrong.
Question 5: answer and source
A major beam on a building structure, is known as
Answer: all the above
Girder, floor beam and main beam all denote the major beam; key unchanged.
Question 6: answer and source
For simply supported beams, the maximum permitted deflection is
Answer: 1/325 of the span
IS 800:1984 deflection limits: 1/325 of span for simply supported steel beams; key unchanged.
Question 7: answer and source
In a fillet weld placed on the sides of the base, the metal experiences
Answer: all the above
A fillet weld group can experience shear, tension and compression depending on loading, though it is designed on shear; key unchanged.
Question 8: answer and source
Steel is efficiently used in
Answer: under reinforced section
In an under-reinforced section the steel yields before the concrete crushes, so its full strength is used; key unchanged.
Question 9: answer and source
The maximum area of tension reinforcement in a beam is
Answer: 4% of bD
IS 456 clause 26.5.1.1 caps beam reinforcement at 4% of bD; key unchanged.
Question 10: answer and source
The large moment of resistance of T-beam section is due to
Answer: composite action between the flanges and the rib
The flange and rib act compositely, giving the T-beam its large moment of resistance; key unchanged.
Question 11: answer and source
If in any given plane, one end of a column is unrestrained, its unsupported length l, shall not exceed
Answer: 100 b^2 /D
IS 456 clause 25.3.2: not more than 60b, or 100b^2/D where D is the depth of the cross-section. Stem typo corrected ('pane' to 'plane'); key unchanged.
Question 12: answer and source
The diameter of lateral ties in a column shall not be less than
Answer: 6 mm
IS 456:2000 clause 26.5.3.2(c): lateral tie diameter at least one-fourth of the largest longitudinal bar and in no case less than 6 mm. Legacy key '5 mm' was the superseded IS 456:1978 value.
Question 13: answer and source
The bending moment at a section of a beam is given by wx^3/6 then the expression for the rate of loading is
Answer: wx
Rate of loading = d2M/dx2 = d2(wx^3/6)/dx2 = wx (wx^2/2 is the shear force, not the loading). Legacy key 'wx^2/2' was wrong.
Question 14: answer and source
The torque produced in a circular shaft rotating at 100 r.p.m. to produce 1 h.p. is _____ Kgcm
Answer: 716.2
T = 71620 x HP / N = 71620 x 1 / 100 = 716.2 kg-cm; key unchanged.
Question 15: answer and source
The weight of foundation may be assumed to be
Answer: 10% of the column loads
Foundation (plus backfill) weight is conventionally taken as about 10% of the column load; key unchanged.
Question 16: answer and source
In a continuous footing the area of longitudinal reinforcement required in the direction of wall is
Answer: 0.3%
Textbook practice for continuous (wall) footings: longitudinal steel 0.3% of the section; key unchanged.
Question 17: answer and source
The net upward pressure on footing p is given by
Answer: W.q./W + W1
With soil capacity q, column load W and footing weight W1: area A = (W+W1)/q, so net upward pressure = W/A = Wq/(W+W1); key unchanged.
Question 18: answer and source
Partial safety factor m for steel in limit state design is
Answer: 1.15
IS 456 clause 36.4.2.1: gamma_m = 1.15 for steel (1.5 for concrete); key unchanged.
Question 19: answer and source
The design strength of materials Fs is given by
Answer: f/Rm
Design strength = characteristic strength / partial safety factor (f/gamma_m); key unchanged.
Question 20: answer and source
The pre-stressed concrete induces artificially _____ stress in a structure before it is loaded
Answer: compressive
Prestressing pre-compresses the concrete so service loads first cancel that compression. Legacy key 'bending' was wrong.
Question 21: answer and source
According to IS code the total amount of shrinkage for a post tensioned member is taken as
Answer: 2 x 10^-4 / log10 (T+2)
IS 1343 clause 5.2.4.1: shrinkage strain for post-tensioned members = 0.0002 / log10(t+2). Legacy option A had a misprint ('10^4') and the legacy key '2 x 10^-3 / log10 (T+3)' was wrong; option corrected and re-keyed.
Question 22: answer and source
The state at which tendon force is released permanently on the concrete is called
Answer: Transfer
Transfer is the stage when the tendon force passes permanently into the concrete. Legacy key 'Pre-tensioning' was wrong.
Question 23: answer and source
In a thin cylindrical shell if F1 is the hoop stress and F2 is the longitudinal stress induced, maximum shear stress at any point of the material is given by
Answer: F1 - F2 / 2
Maximum in-plane shear stress = (sigma1 - sigma2)/2 = (F1 - F2)/2. Legacy key '(F1 + F2)/2' was wrong.
Question 24: answer and source
A beam is fixed at one end and is supported at the other end to the level of the fixed end by means of a rigid prop. At the propped end, for any applied load
Answer: the flexural moment as well as deflection is zero
A simple support offers no moment restraint (moment zero) and the rigid prop prevents settlement (deflection zero); only the slope is free. Legacy key 'only flexural moment is zero' was incomplete and wrong.
Question 25: answer and source
The thickness of lacing bar used in steel ties should not be less than
Answer: L/40
IS 800 clause 7.6.3: lacing flat thickness at least 1/40 of its effective length between connections (single lacing). Legacy key '4.5 mm' was wrong.
Question 26: answer and source
Mohr's theorem I gives _____ between two tangents on the elastic line of beams
Answer: Slope
The first moment-area theorem gives the change of slope between two tangents to the elastic curve (area of the M/EI diagram). Legacy key 'B.M.' was wrong.
Question 27: answer and source
IS code of practice for steel is
Answer: 800
IS 800 is the code for general construction in steel; key unchanged.
Question 28: answer and source
Select cash/commercial crop from the following
Answer: Cotton
Cotton is grown for sale as a fibre crop, i.e. a cash crop; key unchanged.
Question 29: answer and source
Canal lining
Answer: Decreases water logging area
Lining cuts seepage from the canal, which reduces the rise of the water table and hence water logging; key unchanged.
Question 30: answer and source
The diameter of transverse reinforcement of columns should be equal to 1/4 of the diameter of the main steel rods but not less than
Answer: 6 mm
IS 456:2000 clause 26.5.3.2(c): not less than one-fourth of the largest bar diameter and in no case less than 6 mm. Legacy key '7 mm' was wrong.
Change log: 17 November 2026
Original question numbers and review decisions
- Original Q1: verified as keyed. Post-publish correction 2026-11-17: Unwin formula is d = 6.05 x sqrt(t) mm (French formula d = 1.5t + 4). Legacy options contained only 1.91-family values (misprint); replaced the option set and keyed 6.05 sqrt(t).
- Original Q2: corrected. When the member is supported all along, its effective buckling length is zero, so the slenderness ratio is zero. Legacy key 'between the points of zero moments' was wrong.
- Original Q3: verified as keyed. IS 800 designs lacings for a transverse shear of 2.5% of the axial force in the member; stem punctuation cleaned; key unchanged.
- Original Q4: corrected. Very long tension members (e.g. suspension cables) use wires/wire ropes. Legacy key 'a bar is used' was wrong.
- Original Q5: verified as keyed. Girder, floor beam and main beam all denote the major beam; key unchanged.
- Original Q6: verified as keyed. IS 800:1984 deflection limits: 1/325 of span for simply supported steel beams; key unchanged.
- Original Q8: verified as keyed. A fillet weld group can experience shear, tension and compression depending on loading, though it is designed on shear; key unchanged.
- Original Q9: verified as keyed. In an under-reinforced section the steel yields before the concrete crushes, so its full strength is used; key unchanged.
- Original Q10: verified as keyed. IS 456 clause 26.5.1.1 caps beam reinforcement at 4% of bD; key unchanged.
- Original Q11: verified as keyed. The flange and rib act compositely, giving the T-beam its large moment of resistance; key unchanged.
- Original Q12: corrected. IS 456 clause 25.3.2: not more than 60b, or 100b^2/D where D is the depth of the cross-section. Stem typo corrected ('pane' to 'plane'); key unchanged.
- Original Q13: verified as keyed. IS 456:2000 clause 26.5.3.2(c): lateral tie diameter at least one-fourth of the largest longitudinal bar and in no case less than 6 mm. Legacy key '5 mm' was the superseded IS 456:1978 value.
- Original Q14: corrected. Rate of loading = d2M/dx2 = d2(wx^3/6)/dx2 = wx (wx^2/2 is the shear force, not the loading). Legacy key 'wx^2/2' was wrong.
- Original Q15: verified as keyed. T = 71620 x HP / N = 71620 x 1 / 100 = 716.2 kg-cm; key unchanged.
- Original Q16: verified as keyed. Foundation (plus backfill) weight is conventionally taken as about 10% of the column load; key unchanged.
- Original Q17: verified as keyed. Textbook practice for continuous (wall) footings: longitudinal steel 0.3% of the section; key unchanged.
- Original Q18: verified as keyed. With soil capacity q, column load W and footing weight W1: area A = (W+W1)/q, so net upward pressure = W/A = Wq/(W+W1); key unchanged.
- Original Q19: verified as keyed. IS 456 clause 36.4.2.1: gamma_m = 1.15 for steel (1.5 for concrete); key unchanged.
- Original Q20: verified as keyed. Design strength = characteristic strength / partial safety factor (f/gamma_m); key unchanged.
- Original Q21: corrected. Prestressing pre-compresses the concrete so service loads first cancel that compression. Legacy key 'bending' was wrong.
- Original Q22: corrected. IS 1343 clause 5.2.4.1: shrinkage strain for post-tensioned members = 0.0002 / log10(t+2). Legacy option A had a misprint ('10^4') and the legacy key '2 x 10^-3 / log10 (T+3)' was wrong; option corrected and re-keyed.
- Original Q23: corrected. Transfer is the stage when the tendon force passes permanently into the concrete. Legacy key 'Pre-tensioning' was wrong.
- Original Q24: corrected. Maximum in-plane shear stress = (sigma1 - sigma2)/2 = (F1 - F2)/2. Legacy key '(F1 + F2)/2' was wrong.
- Original Q25: corrected. A simple support offers no moment restraint (moment zero) and the rigid prop prevents settlement (deflection zero); only the slope is free. Legacy key 'only flexural moment is zero' was incomplete and wrong.
- Original Q26: corrected. IS 800 clause 7.6.3: lacing flat thickness at least 1/40 of its effective length between connections (single lacing). Legacy key '4.5 mm' was wrong.
- Original Q27: corrected. The first moment-area theorem gives the change of slope between two tangents to the elastic curve (area of the M/EI diagram). Legacy key 'B.M.' was wrong.
- Original Q28: verified as keyed. IS 800 is the code for general construction in steel; key unchanged.
- Original Q29: verified as keyed. Cotton is grown for sale as a fibre crop, i.e. a cash crop; key unchanged.
- Original Q30: verified as keyed. Lining cuts seepage from the canal, which reduces the rise of the water table and hence water logging; key unchanged.
- Original Q31: corrected. IS 456:2000 clause 26.5.3.2(c): not less than one-fourth of the largest bar diameter and in no case less than 6 mm. Legacy key '7 mm' was wrong.
- Original Q7: The correct value is 7 (IS 456 clause 23.2.1 basic span/effective-depth ratio for cantilevers), but 7 is not among the legacy options (4, 8, 12, 16), and the keyed 12 has no code basis. Dropped as unfixable.