Уровень 1
20 reviewed questions. Choose answers, then Calculate. Clear resets all selections. Unanswered questions score zero and remain in the percentage denominator. Open the answer review below for sources.
Answers and sources
Reviewed 17 November 2026. Ambiguous, malformed and unverified legacy questions have been removed. Wording and answer choices have been corrected where needed. This is a study quiz, not certification of engineering or laboratory decisions.
Question 1: answer and source
In a transistor when base-width decreases with increasing collector to base voltage, this phenomenon is called
Answer: Early Effect
Base-width modulation with increasing collector-base voltage is the Early effect.
Question 2: answer and source
An amplifier has a voltage gain of 100. To reduce distortion, 10% negative feedback is employed. The gain of the amplifier with feedback is
Answer: 9.09
Working: A_f = A/(1 + A.beta) = 100/(1 + 100 x 0.1) = 100/11 = 9.09. Legacy key 90.9 is an arithmetic slip.
Question 3: answer and source
The internal impedence of an ideal current source is
Answer: Infinity
An ideal current source has INFINITE internal resistance (current independent of load voltage). 'Zero' describes an ideal voltage source.
Question 4: answer and source
The condition for reciprocity of a two port network is
Answer: AD - BC = 1
Reciprocity in ABCD (transmission) parameters: AD - BC = 1.
Question 5: answer and source
A J-K master slave flip-flop could be converted into a T flip-flop by making
Answer: J = K
JK -> T flip-flop conversion: connect J and K together (J = K = T). Legacy key 'CLK = 0' would freeze the flip-flop.
Question 6: answer and source
The bridge used for measurement of inductance is
Answer: Anderson Bridge
Anderson's bridge measures inductance in terms of a standard capacitor and resistors.
Question 7: answer and source
Lissajou's figures are used in a CRO while measuring
Answer: Frequency
Lissajous patterns compare frequency ratios (and phase) on a CRO.
Question 8: answer and source
The octal number system has
Answer: Eight Different Digits
Octal is base 8: eight digits 0-7. Legacy key 'Seven' wrong.
Question 9: answer and source
Binary multiplication is done using
Answer: Shift and Add
Binary multiplication is done by repeated shift-and-add of partial products.
Question 10: answer and source
A wired AND gate uses
Answer: Open Collector Configuration
Wired-AND is built by tying open-collector outputs together with a pull-up resistor. Legacy key 'Common Emitter' wrong.
Question 11: answer and source
Which of the following is a universal gate?
Answer: NOR
NOR is functionally complete - any logic function can be built from NOR gates alone (shared with NAND).
Question 12: answer and source
The ladder network used in a D/A converter is
Answer: R-2R Ladder
DAC ladder network: R-2R resistor ladder.
Question 13: answer and source
An AM broadcase station transmits 2 KW of carrier power and uses an index of modulation 0.5. The total transmitted power is
Answer: 2.25 KW
Working: P_t = P_c(1 + m^2/2) = 2 x (1 + 0.25/2) = 2 x 1.125 = 2.25 kW.
Question 14: answer and source
If VSWR of transmission line is 4 and its characteristic impedance is 300 ohms. The two possible resistor loads are
Answer: 1200 Ohms and 75 Ohms
Working: R_L = Z0 x S = 300 x 4 = 1200 ohm, or Z0/S = 300/4 = 75 ohm. Legacy key pairs 1200 with 300 - wrong.
Question 15: answer and source
A Zener diode is used for
Answer: Voltage Regulation
A Zener diode in reverse breakdown is used for voltage regulation/reference.
Question 16: answer and source
An SCR is a device having
Answer: Four layers with three junctions
SCR (thyristor): four alternating P-N layers, three junctions.
Question 17: answer and source
An amplifier has a voltage gain of 10,000 expressed in decibels the gain is
Answer: 80
Working (voltage gain): 20 log10(10000) = 20 x 4 = 80 dB. Legacy key 100 wrong; 40 dB would apply only to a power gain. Stem clarified to say voltage gain.
Question 18: answer and source
The amplifier is which current is proportional to the signal voltage, independent of source load resistance is called
Answer: Transconductance amplifier
Transconductance relates output CURRENT to input VOLTAGE - exactly the amplifier described. Legacy key 'Transresistance' (output voltage per input current) wrong.
Question 19: answer and source
An emitter follows has
Answer: High input inpedance and low output impedance.
Emitter follower (common collector): large input impedance, small output impedance.
Question 20: answer and source
To eliminate ghosts in the picture
Answer: Change the antenna orientation or location
Ghosting is multipath; the remedy is correct antenna mounting/orientation toward the transmitter.
Change log: 17 November 2026
Original question numbers and review decisions
- Original Q1: verified. Base-width modulation with increasing collector-base voltage is the Early effect.
- Original Q2: corrected. Working: A_f = A/(1 + A.beta) = 100/(1 + 100 x 0.1) = 100/11 = 9.09. Legacy key 90.9 is an arithmetic slip.
- Original Q3: corrected. An ideal current source has INFINITE internal resistance (current independent of load voltage). 'Zero' describes an ideal voltage source.
- Original Q4: verified. Reciprocity in ABCD (transmission) parameters: AD - BC = 1.
- Original Q5: dropped. The cited figure-eight result depends on small-loop geometry and pattern plane; the stem is unqualified.
- Original Q6: corrected. JK -> T flip-flop conversion: connect J and K together (J = K = T). Legacy key 'CLK = 0' would freeze the flip-flop.
- Original Q7: verified. Anderson's bridge measures inductance in terms of a standard capacitor and resistors.
- Original Q8: dropped. Display digit count does not determine a voltmeter voltage rating.
- Original Q9: verified. Lissajous patterns compare frequency ratios (and phase) on a CRO.
- Original Q10: dropped. The source establishes analogue System B sound modulation, not every TV system; the stem omits that scope.
- Original Q11: dropped. The source establishes legacy analogue System B vision modulation; the stem is not limited to that system or era.
- Original Q12: corrected. Octal is base 8: eight digits 0-7. Legacy key 'Seven' wrong.
- Original Q13: verified. Binary multiplication is done by repeated shift-and-add of partial products.
- Original Q14: corrected. Wired-AND is built by tying open-collector outputs together with a pull-up resistor. Legacy key 'Common Emitter' wrong.
- Original Q15: verified. NOR is functionally complete - any logic function can be built from NOR gates alone (shared with NAND).
- Original Q16: dropped. The source concerns SRAM, while the answer is generic RAM; dynamic RAM does not meet the gates-only description.
- Original Q17: verified. DAC ladder network: R-2R resistor ladder.
- Original Q18: verified. Working: P_t = P_c(1 + m^2/2) = 2 x (1 + 0.25/2) = 2 x 1.125 = 2.25 kW.
- Original Q19: dropped. 455 kHz is conventional for AM broadcast receivers, not all commercial superheterodyne radio receivers.
- Original Q20: dropped. The numerical result is linear noise factor; noise figure is conventionally expressed in dB. The stem does not distinguish them.
- Original Q21: corrected. Working: R_L = Z0 x S = 300 x 4 = 1200 ohm, or Z0/S = 300/4 = 75 ohm. Legacy key pairs 1200 with 300 - wrong.
- Original Q22: verified. A Zener diode in reverse breakdown is used for voltage regulation/reference.
- Original Q23: verified. SCR (thyristor): four alternating P-N layers, three junctions.
- Original Q24: corrected. Working (voltage gain): 20 log10(10000) = 20 x 4 = 80 dB. Legacy key 100 wrong; 40 dB would apply only to a power gain. Stem clarified to say voltage gain.
- Original Q25: dropped. The calculated 40.8 kHz assumes identical single-pole stages and does not establish that the original 400 option was a typo.
- Original Q26: dropped. The source describes common Wien-bridge use but does not support an absolute exclusion from RF operation.
- Original Q27: corrected. Transconductance relates output CURRENT to input VOLTAGE - exactly the amplifier described. Legacy key 'Transresistance' (output voltage per input current) wrong.
- Original Q28: verified. Emitter follower (common collector): large input impedance, small output impedance.
- Original Q29: dropped. The proposed component example is algebraically wrong: R=5 and C=0.4 do not produce 5/(s+2). Drop rather than publish the defective rationale.
- Original Q30: verified. Ghosting is multipath; the remedy is correct antenna mounting/orientation toward the transmitter.