レベル 1


20 reviewed questions. Choose answers, then Calculate. Clear resets all selections. Unanswered questions score zero and remain in the percentage denominator. Open the answer review below for sources.

数値を入力:
計算結果:
%

Answers and sources

Reviewed 17 November 2026. Ambiguous, malformed and unverified legacy questions have been removed. Wording and answer choices have been corrected where needed. This is a study quiz, not certification of engineering or laboratory decisions.

Question 1: answer and source

In a transistor when base-width decreases with increasing collector to base voltage, this phenomenon is called

Answer: Early Effect

Base-width modulation with increasing collector-base voltage is the Early effect.

Source 1

Question 2: answer and source

An amplifier has a voltage gain of 100. To reduce distortion, 10% negative feedback is employed. The gain of the amplifier with feedback is

Answer: 9.09

Working: A_f = A/(1 + A.beta) = 100/(1 + 100 x 0.1) = 100/11 = 9.09. Legacy key 90.9 is an arithmetic slip.

Source 1

Question 3: answer and source

The internal impedence of an ideal current source is

Answer: Infinity

An ideal current source has INFINITE internal resistance (current independent of load voltage). 'Zero' describes an ideal voltage source.

Source 1

Question 4: answer and source

The condition for reciprocity of a two port network is

Answer: AD - BC = 1

Reciprocity in ABCD (transmission) parameters: AD - BC = 1.

Source 1

Question 5: answer and source

A J-K master slave flip-flop could be converted into a T flip-flop by making

Answer: J = K

JK -> T flip-flop conversion: connect J and K together (J = K = T). Legacy key 'CLK = 0' would freeze the flip-flop.

Source 1

Question 6: answer and source

The bridge used for measurement of inductance is

Answer: Anderson Bridge

Anderson's bridge measures inductance in terms of a standard capacitor and resistors.

Source 1

Question 7: answer and source

Lissajou's figures are used in a CRO while measuring

Answer: Frequency

Lissajous patterns compare frequency ratios (and phase) on a CRO.

Source 1

Question 8: answer and source

The octal number system has

Answer: Eight Different Digits

Octal is base 8: eight digits 0-7. Legacy key 'Seven' wrong.

Source 1

Question 9: answer and source

Binary multiplication is done using

Answer: Shift and Add

Binary multiplication is done by repeated shift-and-add of partial products.

Source 1

Question 10: answer and source

A wired AND gate uses

Answer: Open Collector Configuration

Wired-AND is built by tying open-collector outputs together with a pull-up resistor. Legacy key 'Common Emitter' wrong.

Source 1

Question 11: answer and source

Which of the following is a universal gate?

Answer: NOR

NOR is functionally complete - any logic function can be built from NOR gates alone (shared with NAND).

Source 1

Question 12: answer and source

The ladder network used in a D/A converter is

Answer: R-2R Ladder

DAC ladder network: R-2R resistor ladder.

Source 1

Question 13: answer and source

An AM broadcase station transmits 2 KW of carrier power and uses an index of modulation 0.5. The total transmitted power is

Answer: 2.25 KW

Working: P_t = P_c(1 + m^2/2) = 2 x (1 + 0.25/2) = 2 x 1.125 = 2.25 kW.

Source 1

Question 14: answer and source

If VSWR of transmission line is 4 and its characteristic impedance is 300 ohms. The two possible resistor loads are

Answer: 1200 Ohms and 75 Ohms

Working: R_L = Z0 x S = 300 x 4 = 1200 ohm, or Z0/S = 300/4 = 75 ohm. Legacy key pairs 1200 with 300 - wrong.

Source 1

Question 15: answer and source

A Zener diode is used for

Answer: Voltage Regulation

A Zener diode in reverse breakdown is used for voltage regulation/reference.

Source 1

Question 16: answer and source

An SCR is a device having

Answer: Four layers with three junctions

SCR (thyristor): four alternating P-N layers, three junctions.

Source 1

Question 17: answer and source

An amplifier has a voltage gain of 10,000 expressed in decibels the gain is

Answer: 80

Working (voltage gain): 20 log10(10000) = 20 x 4 = 80 dB. Legacy key 100 wrong; 40 dB would apply only to a power gain. Stem clarified to say voltage gain.

Source 1

Question 18: answer and source

The amplifier is which current is proportional to the signal voltage, independent of source load resistance is called

Answer: Transconductance amplifier

Transconductance relates output CURRENT to input VOLTAGE - exactly the amplifier described. Legacy key 'Transresistance' (output voltage per input current) wrong.

Source 1

Question 19: answer and source

An emitter follows has

Answer: High input inpedance and low output impedance.

Emitter follower (common collector): large input impedance, small output impedance.

Source 1

Question 20: answer and source

To eliminate ghosts in the picture

Answer: Change the antenna orientation or location

Ghosting is multipath; the remedy is correct antenna mounting/orientation toward the transmitter.

Source 1

Change log: 17 November 2026

Original question numbers and review decisions
  • Original Q1: verified. Base-width modulation with increasing collector-base voltage is the Early effect.
  • Original Q2: corrected. Working: A_f = A/(1 + A.beta) = 100/(1 + 100 x 0.1) = 100/11 = 9.09. Legacy key 90.9 is an arithmetic slip.
  • Original Q3: corrected. An ideal current source has INFINITE internal resistance (current independent of load voltage). 'Zero' describes an ideal voltage source.
  • Original Q4: verified. Reciprocity in ABCD (transmission) parameters: AD - BC = 1.
  • Original Q5: dropped. The cited figure-eight result depends on small-loop geometry and pattern plane; the stem is unqualified.
  • Original Q6: corrected. JK -> T flip-flop conversion: connect J and K together (J = K = T). Legacy key 'CLK = 0' would freeze the flip-flop.
  • Original Q7: verified. Anderson's bridge measures inductance in terms of a standard capacitor and resistors.
  • Original Q8: dropped. Display digit count does not determine a voltmeter voltage rating.
  • Original Q9: verified. Lissajous patterns compare frequency ratios (and phase) on a CRO.
  • Original Q10: dropped. The source establishes analogue System B sound modulation, not every TV system; the stem omits that scope.
  • Original Q11: dropped. The source establishes legacy analogue System B vision modulation; the stem is not limited to that system or era.
  • Original Q12: corrected. Octal is base 8: eight digits 0-7. Legacy key 'Seven' wrong.
  • Original Q13: verified. Binary multiplication is done by repeated shift-and-add of partial products.
  • Original Q14: corrected. Wired-AND is built by tying open-collector outputs together with a pull-up resistor. Legacy key 'Common Emitter' wrong.
  • Original Q15: verified. NOR is functionally complete - any logic function can be built from NOR gates alone (shared with NAND).
  • Original Q16: dropped. The source concerns SRAM, while the answer is generic RAM; dynamic RAM does not meet the gates-only description.
  • Original Q17: verified. DAC ladder network: R-2R resistor ladder.
  • Original Q18: verified. Working: P_t = P_c(1 + m^2/2) = 2 x (1 + 0.25/2) = 2 x 1.125 = 2.25 kW.
  • Original Q19: dropped. 455 kHz is conventional for AM broadcast receivers, not all commercial superheterodyne radio receivers.
  • Original Q20: dropped. The numerical result is linear noise factor; noise figure is conventionally expressed in dB. The stem does not distinguish them.
  • Original Q21: corrected. Working: R_L = Z0 x S = 300 x 4 = 1200 ohm, or Z0/S = 300/4 = 75 ohm. Legacy key pairs 1200 with 300 - wrong.
  • Original Q22: verified. A Zener diode in reverse breakdown is used for voltage regulation/reference.
  • Original Q23: verified. SCR (thyristor): four alternating P-N layers, three junctions.
  • Original Q24: corrected. Working (voltage gain): 20 log10(10000) = 20 x 4 = 80 dB. Legacy key 100 wrong; 40 dB would apply only to a power gain. Stem clarified to say voltage gain.
  • Original Q25: dropped. The calculated 40.8 kHz assumes identical single-pole stages and does not establish that the original 400 option was a typo.
  • Original Q26: dropped. The source describes common Wien-bridge use but does not support an absolute exclusion from RF operation.
  • Original Q27: corrected. Transconductance relates output CURRENT to input VOLTAGE - exactly the amplifier described. Legacy key 'Transresistance' (output voltage per input current) wrong.
  • Original Q28: verified. Emitter follower (common collector): large input impedance, small output impedance.
  • Original Q29: dropped. The proposed component example is algebraically wrong: R=5 and C=0.4 do not produce 5/(s+2). Drop rather than publish the defective rationale.
  • Original Q30: verified. Ghosting is multipath; the remedy is correct antenna mounting/orientation toward the transmitter.