Stufe 1


20 reviewed questions. Choose answers, then Calculate. Clear resets all selections. Unanswered questions score zero and remain in the percentage denominator. Open the answer review below for sources.

Geben Sie Ihre Werte ein:
Ergebnisse:
%

Answers and sources

Reviewed 17 November 2026. Ambiguous, malformed and unverified legacy questions have been removed. Wording and answer choices have been corrected where needed. This is a study quiz, not certification of engineering or laboratory decisions.

Question 1: answer and source

In a transistor when base-width decreases with increasing collector to base voltage, this phenomenon is called

Answer: Early Effect

Base-width modulation with increasing collector-base voltage is the Early effect.

Source 1

Question 2: answer and source

An amplifier has a voltage gain of 100. To reduce distortion, 10% negative feedback is employed. The gain of the amplifier with feedback is

Answer: 9.09

Working: A_f = A/(1 + A.beta) = 100/(1 + 100 x 0.1) = 100/11 = 9.09. Legacy key 90.9 is an arithmetic slip.

Source 1

Question 3: answer and source

The internal impedence of an ideal current source is

Answer: Infinity

An ideal current source has INFINITE internal resistance (current independent of load voltage). 'Zero' describes an ideal voltage source.

Source 1

Question 4: answer and source

The condition for reciprocity of a two port network is

Answer: AD - BC = 1

Reciprocity in ABCD (transmission) parameters: AD - BC = 1.

Source 1

Question 5: answer and source

A J-K master slave flip-flop could be converted into a T flip-flop by making

Answer: J = K

JK -> T flip-flop conversion: connect J and K together (J = K = T). Legacy key 'CLK = 0' would freeze the flip-flop.

Source 1

Question 6: answer and source

The bridge used for measurement of inductance is

Answer: Anderson Bridge

Anderson's bridge measures inductance in terms of a standard capacitor and resistors.

Source 1

Question 7: answer and source

Lissajou's figures are used in a CRO while measuring

Answer: Frequency

Lissajous patterns compare frequency ratios (and phase) on a CRO.

Source 1

Question 8: answer and source

The octal number system has

Answer: Eight Different Digits

Octal is base 8: eight digits 0-7. Legacy key 'Seven' wrong.

Source 1

Question 9: answer and source

Binary multiplication is done using

Answer: Shift and Add

Binary multiplication is done by repeated shift-and-add of partial products.

Source 1

Question 10: answer and source

A wired AND gate uses

Answer: Open Collector Configuration

Wired-AND is built by tying open-collector outputs together with a pull-up resistor. Legacy key 'Common Emitter' wrong.

Source 1

Question 11: answer and source

Which of the following is a universal gate?

Answer: NOR

NOR is functionally complete - any logic function can be built from NOR gates alone (shared with NAND).

Source 1

Question 12: answer and source

The ladder network used in a D/A converter is

Answer: R-2R Ladder

DAC ladder network: R-2R resistor ladder.

Source 1

Question 13: answer and source

An AM broadcase station transmits 2 KW of carrier power and uses an index of modulation 0.5. The total transmitted power is

Answer: 2.25 KW

Working: P_t = P_c(1 + m^2/2) = 2 x (1 + 0.25/2) = 2 x 1.125 = 2.25 kW.

Source 1

Question 14: answer and source

If VSWR of transmission line is 4 and its characteristic impedance is 300 ohms. The two possible resistor loads are

Answer: 1200 Ohms and 75 Ohms

Working: R_L = Z0 x S = 300 x 4 = 1200 ohm, or Z0/S = 300/4 = 75 ohm. Legacy key pairs 1200 with 300 - wrong.

Source 1

Question 15: answer and source

A Zener diode is used for

Answer: Voltage Regulation

A Zener diode in reverse breakdown is used for voltage regulation/reference.

Source 1

Question 16: answer and source

An SCR is a device having

Answer: Four layers with three junctions

SCR (thyristor): four alternating P-N layers, three junctions.

Source 1

Question 17: answer and source

An amplifier has a voltage gain of 10,000 expressed in decibels the gain is

Answer: 80

Working (voltage gain): 20 log10(10000) = 20 x 4 = 80 dB. Legacy key 100 wrong; 40 dB would apply only to a power gain. Stem clarified to say voltage gain.

Source 1

Question 18: answer and source

The amplifier is which current is proportional to the signal voltage, independent of source load resistance is called

Answer: Transconductance amplifier

Transconductance relates output CURRENT to input VOLTAGE - exactly the amplifier described. Legacy key 'Transresistance' (output voltage per input current) wrong.

Source 1

Question 19: answer and source

An emitter follows has

Answer: High input inpedance and low output impedance.

Emitter follower (common collector): large input impedance, small output impedance.

Source 1

Question 20: answer and source

To eliminate ghosts in the picture

Answer: Change the antenna orientation or location

Ghosting is multipath; the remedy is correct antenna mounting/orientation toward the transmitter.

Source 1

Change log: 17 November 2026

Original question numbers and review decisions
  • Original Q1: verified. Base-width modulation with increasing collector-base voltage is the Early effect.
  • Original Q2: corrected. Working: A_f = A/(1 + A.beta) = 100/(1 + 100 x 0.1) = 100/11 = 9.09. Legacy key 90.9 is an arithmetic slip.
  • Original Q3: corrected. An ideal current source has INFINITE internal resistance (current independent of load voltage). 'Zero' describes an ideal voltage source.
  • Original Q4: verified. Reciprocity in ABCD (transmission) parameters: AD - BC = 1.
  • Original Q5: dropped. The cited figure-eight result depends on small-loop geometry and pattern plane; the stem is unqualified.
  • Original Q6: corrected. JK -> T flip-flop conversion: connect J and K together (J = K = T). Legacy key 'CLK = 0' would freeze the flip-flop.
  • Original Q7: verified. Anderson's bridge measures inductance in terms of a standard capacitor and resistors.
  • Original Q8: dropped. Display digit count does not determine a voltmeter voltage rating.
  • Original Q9: verified. Lissajous patterns compare frequency ratios (and phase) on a CRO.
  • Original Q10: dropped. The source establishes analogue System B sound modulation, not every TV system; the stem omits that scope.
  • Original Q11: dropped. The source establishes legacy analogue System B vision modulation; the stem is not limited to that system or era.
  • Original Q12: corrected. Octal is base 8: eight digits 0-7. Legacy key 'Seven' wrong.
  • Original Q13: verified. Binary multiplication is done by repeated shift-and-add of partial products.
  • Original Q14: corrected. Wired-AND is built by tying open-collector outputs together with a pull-up resistor. Legacy key 'Common Emitter' wrong.
  • Original Q15: verified. NOR is functionally complete - any logic function can be built from NOR gates alone (shared with NAND).
  • Original Q16: dropped. The source concerns SRAM, while the answer is generic RAM; dynamic RAM does not meet the gates-only description.
  • Original Q17: verified. DAC ladder network: R-2R resistor ladder.
  • Original Q18: verified. Working: P_t = P_c(1 + m^2/2) = 2 x (1 + 0.25/2) = 2 x 1.125 = 2.25 kW.
  • Original Q19: dropped. 455 kHz is conventional for AM broadcast receivers, not all commercial superheterodyne radio receivers.
  • Original Q20: dropped. The numerical result is linear noise factor; noise figure is conventionally expressed in dB. The stem does not distinguish them.
  • Original Q21: corrected. Working: R_L = Z0 x S = 300 x 4 = 1200 ohm, or Z0/S = 300/4 = 75 ohm. Legacy key pairs 1200 with 300 - wrong.
  • Original Q22: verified. A Zener diode in reverse breakdown is used for voltage regulation/reference.
  • Original Q23: verified. SCR (thyristor): four alternating P-N layers, three junctions.
  • Original Q24: corrected. Working (voltage gain): 20 log10(10000) = 20 x 4 = 80 dB. Legacy key 100 wrong; 40 dB would apply only to a power gain. Stem clarified to say voltage gain.
  • Original Q25: dropped. The calculated 40.8 kHz assumes identical single-pole stages and does not establish that the original 400 option was a typo.
  • Original Q26: dropped. The source describes common Wien-bridge use but does not support an absolute exclusion from RF operation.
  • Original Q27: corrected. Transconductance relates output CURRENT to input VOLTAGE - exactly the amplifier described. Legacy key 'Transresistance' (output voltage per input current) wrong.
  • Original Q28: verified. Emitter follower (common collector): large input impedance, small output impedance.
  • Original Q29: dropped. The proposed component example is algebraically wrong: R=5 and C=0.4 do not produce 5/(s+2). Drop rather than publish the defective rationale.
  • Original Q30: verified. Ghosting is multipath; the remedy is correct antenna mounting/orientation toward the transmitter.