レベル 1


30 reviewed questions. Choose answers, then Calculate. Clear resets all selections. Unanswered questions score zero and remain in the percentage denominator. Open the answer review below for sources.

数値を入力:
計算結果:
%

Answers and sources

Reviewed 17 November 2026. Ambiguous, malformed and unverified legacy questions have been removed. Wording and answer choices have been corrected where needed. This is a study quiz, not certification of engineering or laboratory decisions.

Question 1: answer and source

For the purpose of comparison, the steam generating capacity of a boiler is generally expressed in terms of

Answer: equivalent evaporation

Boiler output is compared on equivalent evaporation ('from and at 100 deg C'); key unchanged.

Source 1

Question 2: answer and source

One of the following methods is adopted for governing of steam turbines in a power plant

Answer: throttle governing

Principal governing methods are throttle, nozzle and bypass governing; hit-and-miss belongs to steam engines. Key unchanged.

Source 1

Question 3: answer and source

An aircraft gas turbine operates on

Answer: Brayton cycle

Aircraft gas turbines run on the Brayton (Joule) cycle. Option spellings corrected (was 'Bryton', 'Sterling'); key unchanged.

Source 1

Question 4: answer and source

The output of a gas turbine is 300 kW and its efficiency is 20 percent, the heat supplied is

Answer: 1500 kW

Heat supplied = output / efficiency = 300 / 0.2 = 1500 kW. Legacy options lacked the correct value (option '6000 KW' corrected to '1500 kW') and the legacy key '15 KW' was wrong.

Source 1

Question 5: answer and source

Which of the following is not used as a refrigerant?

Answer: carbon monoxide

Ammonia (R717), sulphur dioxide (R764) and carbon dioxide (R744) are all documented refrigerants; carbon monoxide is not. Option spelling corrected ('amonia' to 'ammonia'); key unchanged.

Source 1

Question 6: answer and source

A refrigerant used in the domestic refrigerator is

Answer: freon

Domestic refrigerators historically used Freon (R-12). Stem typo corrected ('refigerant'); key unchanged.

Source 1

Question 7: answer and source

In industry of the developed nations the type of production most often occurring is

Answer: Batch production

Batch production is the standard textbook answer for the most common production type in industry; key unchanged.

Source 1

Question 8: answer and source

Quick return motion is used in a

Answer: shaper

A shaper's ram returns faster on the idle stroke through a quick return mechanism; key unchanged.

Source 1

Question 9: answer and source

Draft on a pattern is provided for

Answer: facilitating withdrawal of the pattern from the mould

Draft (taper) allowance is for easy withdrawal of the pattern from the mould; shrinkage is covered by the shrinkage allowance. Legacy key 'providing for strinkage of the casting' was wrong (typo also corrected).

Source 1

Question 10: answer and source

Which of the following operations cannot be performed on a lathe

Answer: slotting

Lathes perform facing, drilling and thread cutting; slotting needs a slotter/shaper. Key unchanged.

Source 1

Question 11: answer and source

The pump with a low initial cost and low maintenance cost is

Answer: centrifugal pump

Centrifugal pumps combine low cost with low maintenance; key unchanged.

Source 1

Question 12: answer and source

Mandrels are used to hold

Answer: hollow work pieces

A mandrel grips a workpiece through its machined hole, i.e. hollow work pieces; key unchanged.

Source 1

Question 13: answer and source

The operation of enlarging of a hole is called

Answer: boring

Boring is the process of enlarging an already drilled or cast hole; key unchanged.

Source 1

Question 14: answer and source

In upcut milling the work piece is fed

Answer: against the rotating cutter

In up (conventional) milling the feed direction is opposite to cutter rotation; key unchanged.

Source 1

Question 15: answer and source

Sprue is the passage provided for the

Answer: inflow

The sprue is the vertical channel through which molten material is introduced into the mould. Stem typo corrected ('passing' to 'passage'); key unchanged.

Source 1

Question 16: answer and source

Feed in a lathe is expressed in

Answer: mm per revolution

For rotating workpieces (turning, boring) feed is expressed in distance per spindle revolution; key unchanged.

Source 1

Question 17: answer and source

Rapping allowance is provided on a pattern to take care of

Answer: easy withdrawal

Rapping (shake) allowance covers the cavity enlargement when the pattern is rapped for easy withdrawal. Option typo corrected ('withdrawl'); key unchanged.

Source 1

Question 18: answer and source

Upsetting is the term used in one of the following operations

Answer: forging

Upsetting (length decreases, cross-section increases) is a forging operation; key unchanged.

Source 1

Question 19: answer and source

Reducing flame is obtained in oxyacetylene welding with

Answer: excess of acetylene

The carburizing (reducing) flame has excess acetylene. Stem typo corrected ('oxyactetylane'); key unchanged.

Source 1

Question 20: answer and source

Brasses and bronzes are welded using

Answer: oxidizing flames

A strongly oxidizing flame is used for fusion welding brasses and bronzes (controls zinc vaporization). Legacy key 'neutral flame' was wrong.

Source 1

Source 2

Question 21: answer and source

One of the materials used for making surface plate is

Answer: granite

Most modern surface plates are granite; key unchanged.

Source 1

Question 22: answer and source

In a process chart the inverted triangle symbol indicates

Answer: storage

ASME chart symbols: circle = operation, arrow = transport, square = inspection, inverted triangle = storage; key unchanged.

Source 1

Question 23: answer and source

One of the following functions is not performed by coating on the welding electrodes

Answer: increase the cooling rate

Electrode flux shields the weld pool, stabilizes the arc and limits oxidation; it does not increase the cooling rate. Option typo corrected ('refuce'); key unchanged.

Source 1

Question 24: answer and source

Feeler gauges are used for measuring the

Answer: clearances between mating parts

Feeler gauges measure clearances (e.g. valve lash); key unchanged.

Source 1

Question 25: answer and source

A micrometer screw has a pitch of 0.5 mm and the thimble has 100 equal divisions marked on it, the least count of the instrument in mm is

Answer: 0.005

Least count = pitch / thimble divisions = 0.5 / 100 = 0.005 mm. Stem typo corrected ('themble'); key unchanged.

Source 1

Question 26: answer and source

One of the following objectives is not achieved by the process of annealing

Answer: to increase the yield point

Annealing softens metal, relieves internal stress and refines grains; a full anneal lowers yield strength rather than raising it. Key unchanged.

Source 1

Question 27: answer and source

In oxyacetylene welding, acetylene is produced using

Answer: CaC2 and H2O

Acetylene is generated by hydrolysis of calcium carbide (CaC2 + H2O). Stem typo corrected ('oxacetylane'); key unchanged.

Source 1

Question 28: answer and source

A product layout is generally suggested for

Answer: continuous type of production

Product (line) layout suits continuous/mass production; key unchanged.

Source 1

Question 29: answer and source

The break even point is that volume of production where

Answer: no profit exists

At break-even total cost equals total revenue: no profit and no loss; key unchanged.

Source 1

Question 30: answer and source

The melting point of the filler material in brazing should be above

Answer: 420 deg C

Objective-exam convention (RRB JE official paper) keys 420 deg C as the brazing/soldering boundary. Key unchanged.

Source 1

Change log: 17 November 2026

Original question numbers and review decisions
  • Original Q1: verified as keyed. Boiler output is compared on equivalent evaporation ('from and at 100 deg C'); key unchanged.
  • Original Q2: verified as keyed. Principal governing methods are throttle, nozzle and bypass governing; hit-and-miss belongs to steam engines. Key unchanged.
  • Original Q3: corrected. Aircraft gas turbines run on the Brayton (Joule) cycle. Option spellings corrected (was 'Bryton', 'Sterling'); key unchanged.
  • Original Q4: corrected. Heat supplied = output / efficiency = 300 / 0.2 = 1500 kW. Legacy options lacked the correct value (option '6000 KW' corrected to '1500 kW') and the legacy key '15 KW' was wrong.
  • Original Q5: corrected. Ammonia (R717), sulphur dioxide (R764) and carbon dioxide (R744) are all documented refrigerants; carbon monoxide is not. Option spelling corrected ('amonia' to 'ammonia'); key unchanged.
  • Original Q6: corrected. Domestic refrigerators historically used Freon (R-12). Stem typo corrected ('refigerant'); key unchanged.
  • Original Q7: verified as keyed. Batch production is the standard textbook answer for the most common production type in industry; key unchanged.
  • Original Q8: verified as keyed. A shaper's ram returns faster on the idle stroke through a quick return mechanism; key unchanged.
  • Original Q9: corrected. Draft (taper) allowance is for easy withdrawal of the pattern from the mould; shrinkage is covered by the shrinkage allowance. Legacy key 'providing for strinkage of the casting' was wrong (typo also corrected).
  • Original Q10: verified as keyed. Lathes perform facing, drilling and thread cutting; slotting needs a slotter/shaper. Key unchanged.
  • Original Q11: verified as keyed. Centrifugal pumps combine low cost with low maintenance; key unchanged.
  • Original Q12: verified as keyed. A mandrel grips a workpiece through its machined hole, i.e. hollow work pieces; key unchanged.
  • Original Q13: verified as keyed. Boring is the process of enlarging an already drilled or cast hole; key unchanged.
  • Original Q14: verified as keyed. In up (conventional) milling the feed direction is opposite to cutter rotation; key unchanged.
  • Original Q15: corrected. The sprue is the vertical channel through which molten material is introduced into the mould. Stem typo corrected ('passing' to 'passage'); key unchanged.
  • Original Q16: verified as keyed. For rotating workpieces (turning, boring) feed is expressed in distance per spindle revolution; key unchanged.
  • Original Q17: corrected. Rapping (shake) allowance covers the cavity enlargement when the pattern is rapped for easy withdrawal. Option typo corrected ('withdrawl'); key unchanged.
  • Original Q18: verified as keyed. Upsetting (length decreases, cross-section increases) is a forging operation; key unchanged.
  • Original Q19: corrected. The carburizing (reducing) flame has excess acetylene. Stem typo corrected ('oxyactetylane'); key unchanged.
  • Original Q20: corrected. A strongly oxidizing flame is used for fusion welding brasses and bronzes (controls zinc vaporization). Legacy key 'neutral flame' was wrong.
  • Original Q21: verified as keyed. Most modern surface plates are granite; key unchanged.
  • Original Q22: verified as keyed. ASME chart symbols: circle = operation, arrow = transport, square = inspection, inverted triangle = storage; key unchanged.
  • Original Q23: corrected. Electrode flux shields the weld pool, stabilizes the arc and limits oxidation; it does not increase the cooling rate. Option typo corrected ('refuce'); key unchanged.
  • Original Q24: verified as keyed. Feeler gauges measure clearances (e.g. valve lash); key unchanged.
  • Original Q25: corrected. Least count = pitch / thimble divisions = 0.5 / 100 = 0.005 mm. Stem typo corrected ('themble'); key unchanged.
  • Original Q26: verified as keyed. Annealing softens metal, relieves internal stress and refines grains; a full anneal lowers yield strength rather than raising it. Key unchanged.
  • Original Q27: corrected. Acetylene is generated by hydrolysis of calcium carbide (CaC2 + H2O). Stem typo corrected ('oxacetylane'); key unchanged.
  • Original Q28: verified as keyed. Product (line) layout suits continuous/mass production; key unchanged.
  • Original Q30: verified as keyed. At break-even total cost equals total revenue: no profit and no loss; key unchanged.
  • Original Q31: verified as keyed. Objective-exam convention (RRB JE official paper) keys 420 deg C as the brazing/soldering boundary. Key unchanged.
  • Original Q29: Dropped. 'The objective of time study is to determine the time taken by' has no valid option: the correct concept (a qualified worker working at a normal pace) is absent, and the legacy key 'efficient machine utilization' does not answer the question.