Stufe 1


30 reviewed questions. Choose answers, then Calculate. Clear resets all selections. Unanswered questions score zero and remain in the percentage denominator. Open the answer review below for sources.

Geben Sie Ihre Werte ein:
Ergebnisse:
%

Answers and sources

Reviewed 17 November 2026. Ambiguous, malformed and unverified legacy questions have been removed. Wording and answer choices have been corrected where needed. This is a study quiz, not certification of engineering or laboratory decisions.

Question 1: answer and source

For the purpose of comparison, the steam generating capacity of a boiler is generally expressed in terms of

Answer: equivalent evaporation

Boiler output is compared on equivalent evaporation ('from and at 100 deg C'); key unchanged.

Source 1

Question 2: answer and source

One of the following methods is adopted for governing of steam turbines in a power plant

Answer: throttle governing

Principal governing methods are throttle, nozzle and bypass governing; hit-and-miss belongs to steam engines. Key unchanged.

Source 1

Question 3: answer and source

An aircraft gas turbine operates on

Answer: Brayton cycle

Aircraft gas turbines run on the Brayton (Joule) cycle. Option spellings corrected (was 'Bryton', 'Sterling'); key unchanged.

Source 1

Question 4: answer and source

The output of a gas turbine is 300 kW and its efficiency is 20 percent, the heat supplied is

Answer: 1500 kW

Heat supplied = output / efficiency = 300 / 0.2 = 1500 kW. Legacy options lacked the correct value (option '6000 KW' corrected to '1500 kW') and the legacy key '15 KW' was wrong.

Source 1

Question 5: answer and source

Which of the following is not used as a refrigerant?

Answer: carbon monoxide

Ammonia (R717), sulphur dioxide (R764) and carbon dioxide (R744) are all documented refrigerants; carbon monoxide is not. Option spelling corrected ('amonia' to 'ammonia'); key unchanged.

Source 1

Question 6: answer and source

A refrigerant used in the domestic refrigerator is

Answer: freon

Domestic refrigerators historically used Freon (R-12). Stem typo corrected ('refigerant'); key unchanged.

Source 1

Question 7: answer and source

In industry of the developed nations the type of production most often occurring is

Answer: Batch production

Batch production is the standard textbook answer for the most common production type in industry; key unchanged.

Source 1

Question 8: answer and source

Quick return motion is used in a

Answer: shaper

A shaper's ram returns faster on the idle stroke through a quick return mechanism; key unchanged.

Source 1

Question 9: answer and source

Draft on a pattern is provided for

Answer: facilitating withdrawal of the pattern from the mould

Draft (taper) allowance is for easy withdrawal of the pattern from the mould; shrinkage is covered by the shrinkage allowance. Legacy key 'providing for strinkage of the casting' was wrong (typo also corrected).

Source 1

Question 10: answer and source

Which of the following operations cannot be performed on a lathe

Answer: slotting

Lathes perform facing, drilling and thread cutting; slotting needs a slotter/shaper. Key unchanged.

Source 1

Question 11: answer and source

The pump with a low initial cost and low maintenance cost is

Answer: centrifugal pump

Centrifugal pumps combine low cost with low maintenance; key unchanged.

Source 1

Question 12: answer and source

Mandrels are used to hold

Answer: hollow work pieces

A mandrel grips a workpiece through its machined hole, i.e. hollow work pieces; key unchanged.

Source 1

Question 13: answer and source

The operation of enlarging of a hole is called

Answer: boring

Boring is the process of enlarging an already drilled or cast hole; key unchanged.

Source 1

Question 14: answer and source

In upcut milling the work piece is fed

Answer: against the rotating cutter

In up (conventional) milling the feed direction is opposite to cutter rotation; key unchanged.

Source 1

Question 15: answer and source

Sprue is the passage provided for the

Answer: inflow

The sprue is the vertical channel through which molten material is introduced into the mould. Stem typo corrected ('passing' to 'passage'); key unchanged.

Source 1

Question 16: answer and source

Feed in a lathe is expressed in

Answer: mm per revolution

For rotating workpieces (turning, boring) feed is expressed in distance per spindle revolution; key unchanged.

Source 1

Question 17: answer and source

Rapping allowance is provided on a pattern to take care of

Answer: easy withdrawal

Rapping (shake) allowance covers the cavity enlargement when the pattern is rapped for easy withdrawal. Option typo corrected ('withdrawl'); key unchanged.

Source 1

Question 18: answer and source

Upsetting is the term used in one of the following operations

Answer: forging

Upsetting (length decreases, cross-section increases) is a forging operation; key unchanged.

Source 1

Question 19: answer and source

Reducing flame is obtained in oxyacetylene welding with

Answer: excess of acetylene

The carburizing (reducing) flame has excess acetylene. Stem typo corrected ('oxyactetylane'); key unchanged.

Source 1

Question 20: answer and source

Brasses and bronzes are welded using

Answer: oxidizing flames

A strongly oxidizing flame is used for fusion welding brasses and bronzes (controls zinc vaporization). Legacy key 'neutral flame' was wrong.

Source 1

Source 2

Question 21: answer and source

One of the materials used for making surface plate is

Answer: granite

Most modern surface plates are granite; key unchanged.

Source 1

Question 22: answer and source

In a process chart the inverted triangle symbol indicates

Answer: storage

ASME chart symbols: circle = operation, arrow = transport, square = inspection, inverted triangle = storage; key unchanged.

Source 1

Question 23: answer and source

One of the following functions is not performed by coating on the welding electrodes

Answer: increase the cooling rate

Electrode flux shields the weld pool, stabilizes the arc and limits oxidation; it does not increase the cooling rate. Option typo corrected ('refuce'); key unchanged.

Source 1

Question 24: answer and source

Feeler gauges are used for measuring the

Answer: clearances between mating parts

Feeler gauges measure clearances (e.g. valve lash); key unchanged.

Source 1

Question 25: answer and source

A micrometer screw has a pitch of 0.5 mm and the thimble has 100 equal divisions marked on it, the least count of the instrument in mm is

Answer: 0.005

Least count = pitch / thimble divisions = 0.5 / 100 = 0.005 mm. Stem typo corrected ('themble'); key unchanged.

Source 1

Question 26: answer and source

One of the following objectives is not achieved by the process of annealing

Answer: to increase the yield point

Annealing softens metal, relieves internal stress and refines grains; a full anneal lowers yield strength rather than raising it. Key unchanged.

Source 1

Question 27: answer and source

In oxyacetylene welding, acetylene is produced using

Answer: CaC2 and H2O

Acetylene is generated by hydrolysis of calcium carbide (CaC2 + H2O). Stem typo corrected ('oxacetylane'); key unchanged.

Source 1

Question 28: answer and source

A product layout is generally suggested for

Answer: continuous type of production

Product (line) layout suits continuous/mass production; key unchanged.

Source 1

Question 29: answer and source

The break even point is that volume of production where

Answer: no profit exists

At break-even total cost equals total revenue: no profit and no loss; key unchanged.

Source 1

Question 30: answer and source

The melting point of the filler material in brazing should be above

Answer: 420 deg C

Objective-exam convention (RRB JE official paper) keys 420 deg C as the brazing/soldering boundary. Key unchanged.

Source 1

Change log: 17 November 2026

Original question numbers and review decisions
  • Original Q1: verified as keyed. Boiler output is compared on equivalent evaporation ('from and at 100 deg C'); key unchanged.
  • Original Q2: verified as keyed. Principal governing methods are throttle, nozzle and bypass governing; hit-and-miss belongs to steam engines. Key unchanged.
  • Original Q3: corrected. Aircraft gas turbines run on the Brayton (Joule) cycle. Option spellings corrected (was 'Bryton', 'Sterling'); key unchanged.
  • Original Q4: corrected. Heat supplied = output / efficiency = 300 / 0.2 = 1500 kW. Legacy options lacked the correct value (option '6000 KW' corrected to '1500 kW') and the legacy key '15 KW' was wrong.
  • Original Q5: corrected. Ammonia (R717), sulphur dioxide (R764) and carbon dioxide (R744) are all documented refrigerants; carbon monoxide is not. Option spelling corrected ('amonia' to 'ammonia'); key unchanged.
  • Original Q6: corrected. Domestic refrigerators historically used Freon (R-12). Stem typo corrected ('refigerant'); key unchanged.
  • Original Q7: verified as keyed. Batch production is the standard textbook answer for the most common production type in industry; key unchanged.
  • Original Q8: verified as keyed. A shaper's ram returns faster on the idle stroke through a quick return mechanism; key unchanged.
  • Original Q9: corrected. Draft (taper) allowance is for easy withdrawal of the pattern from the mould; shrinkage is covered by the shrinkage allowance. Legacy key 'providing for strinkage of the casting' was wrong (typo also corrected).
  • Original Q10: verified as keyed. Lathes perform facing, drilling and thread cutting; slotting needs a slotter/shaper. Key unchanged.
  • Original Q11: verified as keyed. Centrifugal pumps combine low cost with low maintenance; key unchanged.
  • Original Q12: verified as keyed. A mandrel grips a workpiece through its machined hole, i.e. hollow work pieces; key unchanged.
  • Original Q13: verified as keyed. Boring is the process of enlarging an already drilled or cast hole; key unchanged.
  • Original Q14: verified as keyed. In up (conventional) milling the feed direction is opposite to cutter rotation; key unchanged.
  • Original Q15: corrected. The sprue is the vertical channel through which molten material is introduced into the mould. Stem typo corrected ('passing' to 'passage'); key unchanged.
  • Original Q16: verified as keyed. For rotating workpieces (turning, boring) feed is expressed in distance per spindle revolution; key unchanged.
  • Original Q17: corrected. Rapping (shake) allowance covers the cavity enlargement when the pattern is rapped for easy withdrawal. Option typo corrected ('withdrawl'); key unchanged.
  • Original Q18: verified as keyed. Upsetting (length decreases, cross-section increases) is a forging operation; key unchanged.
  • Original Q19: corrected. The carburizing (reducing) flame has excess acetylene. Stem typo corrected ('oxyactetylane'); key unchanged.
  • Original Q20: corrected. A strongly oxidizing flame is used for fusion welding brasses and bronzes (controls zinc vaporization). Legacy key 'neutral flame' was wrong.
  • Original Q21: verified as keyed. Most modern surface plates are granite; key unchanged.
  • Original Q22: verified as keyed. ASME chart symbols: circle = operation, arrow = transport, square = inspection, inverted triangle = storage; key unchanged.
  • Original Q23: corrected. Electrode flux shields the weld pool, stabilizes the arc and limits oxidation; it does not increase the cooling rate. Option typo corrected ('refuce'); key unchanged.
  • Original Q24: verified as keyed. Feeler gauges measure clearances (e.g. valve lash); key unchanged.
  • Original Q25: corrected. Least count = pitch / thimble divisions = 0.5 / 100 = 0.005 mm. Stem typo corrected ('themble'); key unchanged.
  • Original Q26: verified as keyed. Annealing softens metal, relieves internal stress and refines grains; a full anneal lowers yield strength rather than raising it. Key unchanged.
  • Original Q27: corrected. Acetylene is generated by hydrolysis of calcium carbide (CaC2 + H2O). Stem typo corrected ('oxacetylane'); key unchanged.
  • Original Q28: verified as keyed. Product (line) layout suits continuous/mass production; key unchanged.
  • Original Q30: verified as keyed. At break-even total cost equals total revenue: no profit and no loss; key unchanged.
  • Original Q31: verified as keyed. Objective-exam convention (RRB JE official paper) keys 420 deg C as the brazing/soldering boundary. Key unchanged.
  • Original Q29: Dropped. 'The objective of time study is to determine the time taken by' has no valid option: the correct concept (a qualified worker working at a normal pace) is absent, and the legacy key 'efficient machine utilization' does not answer the question.