レベル 5


31 reviewed questions. Choose answers, then Calculate. Clear resets all selections. Unanswered questions score zero and remain in the percentage denominator. Open the answer review below for sources.

数値を入力:
計算結果:
%

Answers and sources

Reviewed 17 November 2026. Ambiguous, malformed and unverified legacy questions have been removed. Wording and answer choices have been corrected where needed. This is a study quiz, not certification of engineering or laboratory decisions.

Question 1: answer and source

The centre of pressure of a plane submerged area is

Answer: always below the centre of gravity of the area

Centre of pressure of a submerged plane lies below its centroid (pressure increases with depth); legacy keyed 'above the centroid'.

Source 1

Question 2: answer and source

The forces coming over the dam are mainly resisted by

Answer: self weight of the dam

A gravity dam resists the water thrust mainly by its own weight; key unchanged.

Source 1

Question 3: answer and source

The turbine in which the runner blades move and adjust themselves during the operation of turbine is called _____ turbine

Answer: Kaplan

Kaplan turbines have adjustable runner blades (and wicket gates); key unchanged.

Source 1

Question 4: answer and source

A centrifugal pump converts _____ energy into hydraulic energy

Answer: mechanical

A centrifugal pump converts mechanical (shaft) energy into hydraulic energy; legacy keyed 'pressure'.

Source 1

Question 5: answer and source

Falling drops of rain acquire spherical shape on account of

Answer: surface tension

Surface tension minimises surface area, making drops spherical; legacy keyed 'viscosity'.

Source 1

Question 6: answer and source

The vertical component of pressure force on a submerged curved surface is equal to

Answer: the weight of liquid vertically above the curved surface

Vertical component equals the weight of liquid vertically above the curved surface up to the free surface; legacy keyed pressure x area.

Source 1

Question 7: answer and source

Coefficient of resistance Cr for an orifice is equal to

Answer: (1/Cv^2 - 1)

From Cv = 1/sqrt(1+Cr), Cr = 1/Cv^2 - 1; key unchanged.

Question 8: answer and source

A hydraulic jump is used for

Answer: reducing the energy of flow

Stilling basins use hydraulic jumps to dissipate the mechanical energy of the flow; legacy keyed 'decreasing the velocity'.

Source 1

Question 9: answer and source

For laminar flow through a pipe, the energy correction factor is

Answer: 2.00

Kinetic energy correction factor alpha = 2 for laminar pipe flow; key unchanged.

Question 10: answer and source

The force required to act upon the jet of water to change the velocity either in direction or in magnitude is called

Answer: dynamic force

Force that changes a jet's velocity is the dynamic force (impact of jet, impulse-momentum); legacy keyed 'power canal' (corrupted option merge).

Question 11: answer and source

The canal through which water is led into mouth of the penstocks is

Answer: power canal

The power canal leads water to the penstocks; key unchanged. Fixed misprint 'fore day' to 'fore bay'.

Question 12: answer and source

The device fitted to a reciprocating pump for smooth and uniform flow is called

Answer: air vessel

An air vessel fitted to suction/delivery pipe of a reciprocating pump gives smooth, uniform flow; legacy keyed 'impeller'.

Question 13: answer and source

Surge tank is provided to prevent the effect of

Answer: water hammer

A surge tank absorbs pressure surges from water hammer in the penstock; key unchanged.

Source 1

Question 14: answer and source

The minimum distance between centres of rivet holes should be

Answer: 2.5 times the hole diameter

IS 800 minimum pitch = 2.5 times the nominal rivet diameter; legacy keyed 1.5 times.

Source 1

Question 15: answer and source

In turbine governing system, the pump used is

Answer: gear pump

Turbine governing (oil pressure) systems use gear pumps; key unchanged.

Question 16: answer and source

Bombay harbour is an example of _____ harbour

Answer: natural

Mumbai (Bombay) Harbour is a natural deep-water harbour; legacy keyed 'artificial'.

Source 1

Question 17: answer and source

The operation of removal of external material from the sea or river bed is known as

Answer: dredging

Dredging is excavation of material from a water environment; key unchanged.

Source 1

Question 18: answer and source

In case of an external mouth piece the pressure at vena contracta is equal to

Answer: Ha - 0.89 H

Bernoulli applied to an external mouthpiece gives absolute pressure head at vena contracta = Ha - 0.89H; legacy keyed Ha - 0.87H.

Source 1

Question 19: answer and source

If the Young's modulus of elasticity of a material is twice its modulus of rigidity, then the Poisson's ratio of the material is

Answer: 0

E = 2G(1 + mu); with E = 2G, mu = 0; legacy keyed 0.5.

Source 1

Question 20: answer and source

For an isotropic, homogeneous and elastic material obeying Hooke's law, number of independent elastic constants is

Answer: 2

An isotropic elastic material has 2 independent elastic constants (E and mu); key unchanged.

Source 1

Question 21: answer and source

If a material has identical properties in all directions, it is said to be

Answer: isotropic

Isotropic = same properties in all directions (homogeneous = same at all points); legacy keyed 'homogeneous'.

Source 1

Question 22: answer and source

According to Unwin's formula, the diameter of rivet in mm to suit the t mm thickness of plate is given by

Answer: 6 Sqrt(t)

Unwin's formula is d = 6.05 x sqrt(t) mm, i.e. about 6 sqrt(t); 1.5t + 4 is the French formula; legacy keyed 1.9 sqrt(t), which matches no standard formula.

Source 1

Question 23: answer and source

The sum of normal stresses is

Answer: constant

The sum of normal stresses on mutually perpendicular planes is invariant; key unchanged.

Question 24: answer and source

A simply supported beam of length l carries a load varying uniformly from zero at left end to maximum at right end. The maximum bending moment occurs at a distance of

Answer: l/Sqrt(3) from left end

Shear force is zero at x = l/sqrt(3) from the zero-load (left) end, where BM is maximum; legacy keyed l/3 from left end.

Question 25: answer and source

Of the two prismatic beams of same material, length and flexural strength, one is circular and other is square in cross-section, the ratio of weights of circular and square beam is

Answer: 1.118

Equal flexural strength means equal section modulus: pi d^3/32 = b^3/6 gives d = 1.193b, so the weight (area) ratio circle/square = 1.118; legacy keyed 0.793.

Question 26: answer and source

For no torsion, the plane of bending should

Answer: pass through shear centre of section

A load through the shear centre produces bending without torsion; legacy keyed neutral axis.

Source 1

Question 27: answer and source

A beam of uniform strength has at every cross-section same

Answer: bending stress

A beam of uniform strength is shaped so the maximum bending stress is the same at every section; key unchanged.

Question 28: answer and source

Effective length of a column fixed at one end hinged at the other end is

Answer: l/Sqrt(2)

Fixed-hinged column effective length factor K = 1/sqrt(2) (about 0.7); legacy keyed l/2 (that is fixed-fixed).

Source 1

Question 29: answer and source

Soundness of cement is tested by

Answer: Le Chatelier

Soundness of cement (expansion from free lime/MgO) is tested with the Le Chatelier apparatus; Los Angeles is an aggregate abrasion test; legacy keyed Los Angeles. Fixed misprints 'Le chaterlier'/'Los angles'.

Question 30: answer and source

During setting and hardening of concrete _____ is generated

Answer: Heat

Cement hydration is exothermic and generates heat (heat of hydration); legacy keyed 'Energy'.

Question 31: answer and source

In a pre-stressed member it is advisable to use

Answer: high strength concrete and high tensile steel

Prestressed members use high strength concrete with high tensile steel to limit losses; key unchanged.

Source 1

Change log: 17 November 2026

Original question numbers and review decisions
  • Original Q1: verified as keyed. Centre of pressure of a submerged plane lies below its centroid (pressure increases with depth); legacy keyed 'above the centroid'.
  • Original Q2: verified as keyed. A gravity dam resists the water thrust mainly by its own weight; key unchanged.
  • Original Q3: verified as keyed. Kaplan turbines have adjustable runner blades (and wicket gates); key unchanged.
  • Original Q4: verified as keyed. A centrifugal pump converts mechanical (shaft) energy into hydraulic energy; legacy keyed 'pressure'.
  • Original Q5: verified as keyed. Surface tension minimises surface area, making drops spherical; legacy keyed 'viscosity'.
  • Original Q6: verified as keyed. Vertical component equals the weight of liquid vertically above the curved surface up to the free surface; legacy keyed pressure x area.
  • Original Q7: verified as keyed. From Cv = 1/sqrt(1+Cr), Cr = 1/Cv^2 - 1; key unchanged.
  • Original Q8: verified as keyed. Stilling basins use hydraulic jumps to dissipate the mechanical energy of the flow; legacy keyed 'decreasing the velocity'.
  • Original Q9: verified as keyed. Kinetic energy correction factor alpha = 2 for laminar pipe flow; key unchanged.
  • Original Q10: verified as keyed. Force that changes a jet's velocity is the dynamic force (impact of jet, impulse-momentum); legacy keyed 'power canal' (corrupted option merge).
  • Original Q11: verified as keyed. The power canal leads water to the penstocks; key unchanged. Fixed misprint 'fore day' to 'fore bay'.
  • Original Q12: verified as keyed. An air vessel fitted to suction/delivery pipe of a reciprocating pump gives smooth, uniform flow; legacy keyed 'impeller'.
  • Original Q13: verified as keyed. A surge tank absorbs pressure surges from water hammer in the penstock; key unchanged.
  • Original Q14: verified as keyed. IS 800 minimum pitch = 2.5 times the nominal rivet diameter; legacy keyed 1.5 times.
  • Original Q15: verified as keyed. Turbine governing (oil pressure) systems use gear pumps; key unchanged.
  • Original Q16: verified as keyed. Mumbai (Bombay) Harbour is a natural deep-water harbour; legacy keyed 'artificial'.
  • Original Q17: verified as keyed. Dredging is excavation of material from a water environment; key unchanged.
  • Original Q18: verified as keyed. Bernoulli applied to an external mouthpiece gives absolute pressure head at vena contracta = Ha - 0.89H; legacy keyed Ha - 0.87H.
  • Original Q19: verified as keyed. E = 2G(1 + mu); with E = 2G, mu = 0; legacy keyed 0.5.
  • Original Q20: verified as keyed. An isotropic elastic material has 2 independent elastic constants (E and mu); key unchanged.
  • Original Q21: verified as keyed. Isotropic = same properties in all directions (homogeneous = same at all points); legacy keyed 'homogeneous'.
  • Original Q22: verified as keyed. Unwin's formula is d = 6.05 x sqrt(t) mm, i.e. about 6 sqrt(t); 1.5t + 4 is the French formula; legacy keyed 1.9 sqrt(t), which matches no standard formula.
  • Original Q23: verified as keyed. The sum of normal stresses on mutually perpendicular planes is invariant; key unchanged.
  • Original Q24: verified as keyed. Shear force is zero at x = l/sqrt(3) from the zero-load (left) end, where BM is maximum; legacy keyed l/3 from left end.
  • Original Q25: verified as keyed. Equal flexural strength means equal section modulus: pi d^3/32 = b^3/6 gives d = 1.193b, so the weight (area) ratio circle/square = 1.118; legacy keyed 0.793.
  • Original Q26: verified as keyed. A load through the shear centre produces bending without torsion; legacy keyed neutral axis.
  • Original Q27: verified as keyed. A beam of uniform strength is shaped so the maximum bending stress is the same at every section; key unchanged.
  • Original Q28: verified as keyed. Fixed-hinged column effective length factor K = 1/sqrt(2) (about 0.7); legacy keyed l/2 (that is fixed-fixed).
  • Original Q29: verified as keyed. Soundness of cement (expansion from free lime/MgO) is tested with the Le Chatelier apparatus; Los Angeles is an aggregate abrasion test; legacy keyed Los Angeles. Fixed misprints 'Le chaterlier'/'Los angles'.
  • Original Q30: verified as keyed. Cement hydration is exothermic and generates heat (heat of hydration); legacy keyed 'Energy'.
  • Original Q31: verified as keyed. Prestressed members use high strength concrete with high tensile steel to limit losses; key unchanged.