Stufe 5


31 reviewed questions. Choose answers, then Calculate. Clear resets all selections. Unanswered questions score zero and remain in the percentage denominator. Open the answer review below for sources.

Geben Sie Ihre Werte ein:
Ergebnisse:
%

Answers and sources

Reviewed 17 November 2026. Ambiguous, malformed and unverified legacy questions have been removed. Wording and answer choices have been corrected where needed. This is a study quiz, not certification of engineering or laboratory decisions.

Question 1: answer and source

The centre of pressure of a plane submerged area is

Answer: always below the centre of gravity of the area

Centre of pressure of a submerged plane lies below its centroid (pressure increases with depth); legacy keyed 'above the centroid'.

Source 1

Question 2: answer and source

The forces coming over the dam are mainly resisted by

Answer: self weight of the dam

A gravity dam resists the water thrust mainly by its own weight; key unchanged.

Source 1

Question 3: answer and source

The turbine in which the runner blades move and adjust themselves during the operation of turbine is called _____ turbine

Answer: Kaplan

Kaplan turbines have adjustable runner blades (and wicket gates); key unchanged.

Source 1

Question 4: answer and source

A centrifugal pump converts _____ energy into hydraulic energy

Answer: mechanical

A centrifugal pump converts mechanical (shaft) energy into hydraulic energy; legacy keyed 'pressure'.

Source 1

Question 5: answer and source

Falling drops of rain acquire spherical shape on account of

Answer: surface tension

Surface tension minimises surface area, making drops spherical; legacy keyed 'viscosity'.

Source 1

Question 6: answer and source

The vertical component of pressure force on a submerged curved surface is equal to

Answer: the weight of liquid vertically above the curved surface

Vertical component equals the weight of liquid vertically above the curved surface up to the free surface; legacy keyed pressure x area.

Source 1

Question 7: answer and source

Coefficient of resistance Cr for an orifice is equal to

Answer: (1/Cv^2 - 1)

From Cv = 1/sqrt(1+Cr), Cr = 1/Cv^2 - 1; key unchanged.

Question 8: answer and source

A hydraulic jump is used for

Answer: reducing the energy of flow

Stilling basins use hydraulic jumps to dissipate the mechanical energy of the flow; legacy keyed 'decreasing the velocity'.

Source 1

Question 9: answer and source

For laminar flow through a pipe, the energy correction factor is

Answer: 2.00

Kinetic energy correction factor alpha = 2 for laminar pipe flow; key unchanged.

Question 10: answer and source

The force required to act upon the jet of water to change the velocity either in direction or in magnitude is called

Answer: dynamic force

Force that changes a jet's velocity is the dynamic force (impact of jet, impulse-momentum); legacy keyed 'power canal' (corrupted option merge).

Question 11: answer and source

The canal through which water is led into mouth of the penstocks is

Answer: power canal

The power canal leads water to the penstocks; key unchanged. Fixed misprint 'fore day' to 'fore bay'.

Question 12: answer and source

The device fitted to a reciprocating pump for smooth and uniform flow is called

Answer: air vessel

An air vessel fitted to suction/delivery pipe of a reciprocating pump gives smooth, uniform flow; legacy keyed 'impeller'.

Question 13: answer and source

Surge tank is provided to prevent the effect of

Answer: water hammer

A surge tank absorbs pressure surges from water hammer in the penstock; key unchanged.

Source 1

Question 14: answer and source

The minimum distance between centres of rivet holes should be

Answer: 2.5 times the hole diameter

IS 800 minimum pitch = 2.5 times the nominal rivet diameter; legacy keyed 1.5 times.

Source 1

Question 15: answer and source

In turbine governing system, the pump used is

Answer: gear pump

Turbine governing (oil pressure) systems use gear pumps; key unchanged.

Question 16: answer and source

Bombay harbour is an example of _____ harbour

Answer: natural

Mumbai (Bombay) Harbour is a natural deep-water harbour; legacy keyed 'artificial'.

Source 1

Question 17: answer and source

The operation of removal of external material from the sea or river bed is known as

Answer: dredging

Dredging is excavation of material from a water environment; key unchanged.

Source 1

Question 18: answer and source

In case of an external mouth piece the pressure at vena contracta is equal to

Answer: Ha - 0.89 H

Bernoulli applied to an external mouthpiece gives absolute pressure head at vena contracta = Ha - 0.89H; legacy keyed Ha - 0.87H.

Source 1

Question 19: answer and source

If the Young's modulus of elasticity of a material is twice its modulus of rigidity, then the Poisson's ratio of the material is

Answer: 0

E = 2G(1 + mu); with E = 2G, mu = 0; legacy keyed 0.5.

Source 1

Question 20: answer and source

For an isotropic, homogeneous and elastic material obeying Hooke's law, number of independent elastic constants is

Answer: 2

An isotropic elastic material has 2 independent elastic constants (E and mu); key unchanged.

Source 1

Question 21: answer and source

If a material has identical properties in all directions, it is said to be

Answer: isotropic

Isotropic = same properties in all directions (homogeneous = same at all points); legacy keyed 'homogeneous'.

Source 1

Question 22: answer and source

According to Unwin's formula, the diameter of rivet in mm to suit the t mm thickness of plate is given by

Answer: 6 Sqrt(t)

Unwin's formula is d = 6.05 x sqrt(t) mm, i.e. about 6 sqrt(t); 1.5t + 4 is the French formula; legacy keyed 1.9 sqrt(t), which matches no standard formula.

Source 1

Question 23: answer and source

The sum of normal stresses is

Answer: constant

The sum of normal stresses on mutually perpendicular planes is invariant; key unchanged.

Question 24: answer and source

A simply supported beam of length l carries a load varying uniformly from zero at left end to maximum at right end. The maximum bending moment occurs at a distance of

Answer: l/Sqrt(3) from left end

Shear force is zero at x = l/sqrt(3) from the zero-load (left) end, where BM is maximum; legacy keyed l/3 from left end.

Question 25: answer and source

Of the two prismatic beams of same material, length and flexural strength, one is circular and other is square in cross-section, the ratio of weights of circular and square beam is

Answer: 1.118

Equal flexural strength means equal section modulus: pi d^3/32 = b^3/6 gives d = 1.193b, so the weight (area) ratio circle/square = 1.118; legacy keyed 0.793.

Question 26: answer and source

For no torsion, the plane of bending should

Answer: pass through shear centre of section

A load through the shear centre produces bending without torsion; legacy keyed neutral axis.

Source 1

Question 27: answer and source

A beam of uniform strength has at every cross-section same

Answer: bending stress

A beam of uniform strength is shaped so the maximum bending stress is the same at every section; key unchanged.

Question 28: answer and source

Effective length of a column fixed at one end hinged at the other end is

Answer: l/Sqrt(2)

Fixed-hinged column effective length factor K = 1/sqrt(2) (about 0.7); legacy keyed l/2 (that is fixed-fixed).

Source 1

Question 29: answer and source

Soundness of cement is tested by

Answer: Le Chatelier

Soundness of cement (expansion from free lime/MgO) is tested with the Le Chatelier apparatus; Los Angeles is an aggregate abrasion test; legacy keyed Los Angeles. Fixed misprints 'Le chaterlier'/'Los angles'.

Question 30: answer and source

During setting and hardening of concrete _____ is generated

Answer: Heat

Cement hydration is exothermic and generates heat (heat of hydration); legacy keyed 'Energy'.

Question 31: answer and source

In a pre-stressed member it is advisable to use

Answer: high strength concrete and high tensile steel

Prestressed members use high strength concrete with high tensile steel to limit losses; key unchanged.

Source 1

Change log: 17 November 2026

Original question numbers and review decisions
  • Original Q1: verified as keyed. Centre of pressure of a submerged plane lies below its centroid (pressure increases with depth); legacy keyed 'above the centroid'.
  • Original Q2: verified as keyed. A gravity dam resists the water thrust mainly by its own weight; key unchanged.
  • Original Q3: verified as keyed. Kaplan turbines have adjustable runner blades (and wicket gates); key unchanged.
  • Original Q4: verified as keyed. A centrifugal pump converts mechanical (shaft) energy into hydraulic energy; legacy keyed 'pressure'.
  • Original Q5: verified as keyed. Surface tension minimises surface area, making drops spherical; legacy keyed 'viscosity'.
  • Original Q6: verified as keyed. Vertical component equals the weight of liquid vertically above the curved surface up to the free surface; legacy keyed pressure x area.
  • Original Q7: verified as keyed. From Cv = 1/sqrt(1+Cr), Cr = 1/Cv^2 - 1; key unchanged.
  • Original Q8: verified as keyed. Stilling basins use hydraulic jumps to dissipate the mechanical energy of the flow; legacy keyed 'decreasing the velocity'.
  • Original Q9: verified as keyed. Kinetic energy correction factor alpha = 2 for laminar pipe flow; key unchanged.
  • Original Q10: verified as keyed. Force that changes a jet's velocity is the dynamic force (impact of jet, impulse-momentum); legacy keyed 'power canal' (corrupted option merge).
  • Original Q11: verified as keyed. The power canal leads water to the penstocks; key unchanged. Fixed misprint 'fore day' to 'fore bay'.
  • Original Q12: verified as keyed. An air vessel fitted to suction/delivery pipe of a reciprocating pump gives smooth, uniform flow; legacy keyed 'impeller'.
  • Original Q13: verified as keyed. A surge tank absorbs pressure surges from water hammer in the penstock; key unchanged.
  • Original Q14: verified as keyed. IS 800 minimum pitch = 2.5 times the nominal rivet diameter; legacy keyed 1.5 times.
  • Original Q15: verified as keyed. Turbine governing (oil pressure) systems use gear pumps; key unchanged.
  • Original Q16: verified as keyed. Mumbai (Bombay) Harbour is a natural deep-water harbour; legacy keyed 'artificial'.
  • Original Q17: verified as keyed. Dredging is excavation of material from a water environment; key unchanged.
  • Original Q18: verified as keyed. Bernoulli applied to an external mouthpiece gives absolute pressure head at vena contracta = Ha - 0.89H; legacy keyed Ha - 0.87H.
  • Original Q19: verified as keyed. E = 2G(1 + mu); with E = 2G, mu = 0; legacy keyed 0.5.
  • Original Q20: verified as keyed. An isotropic elastic material has 2 independent elastic constants (E and mu); key unchanged.
  • Original Q21: verified as keyed. Isotropic = same properties in all directions (homogeneous = same at all points); legacy keyed 'homogeneous'.
  • Original Q22: verified as keyed. Unwin's formula is d = 6.05 x sqrt(t) mm, i.e. about 6 sqrt(t); 1.5t + 4 is the French formula; legacy keyed 1.9 sqrt(t), which matches no standard formula.
  • Original Q23: verified as keyed. The sum of normal stresses on mutually perpendicular planes is invariant; key unchanged.
  • Original Q24: verified as keyed. Shear force is zero at x = l/sqrt(3) from the zero-load (left) end, where BM is maximum; legacy keyed l/3 from left end.
  • Original Q25: verified as keyed. Equal flexural strength means equal section modulus: pi d^3/32 = b^3/6 gives d = 1.193b, so the weight (area) ratio circle/square = 1.118; legacy keyed 0.793.
  • Original Q26: verified as keyed. A load through the shear centre produces bending without torsion; legacy keyed neutral axis.
  • Original Q27: verified as keyed. A beam of uniform strength is shaped so the maximum bending stress is the same at every section; key unchanged.
  • Original Q28: verified as keyed. Fixed-hinged column effective length factor K = 1/sqrt(2) (about 0.7); legacy keyed l/2 (that is fixed-fixed).
  • Original Q29: verified as keyed. Soundness of cement (expansion from free lime/MgO) is tested with the Le Chatelier apparatus; Los Angeles is an aggregate abrasion test; legacy keyed Los Angeles. Fixed misprints 'Le chaterlier'/'Los angles'.
  • Original Q30: verified as keyed. Cement hydration is exothermic and generates heat (heat of hydration); legacy keyed 'Energy'.
  • Original Q31: verified as keyed. Prestressed members use high strength concrete with high tensile steel to limit losses; key unchanged.