Mechanical Charts


Plain Washers, Black : Metric Series

Comparison of Hardness on Various Scales

Table of Cutting Speeds

Circumferential Speeds for High Speed Twist Drills

Standard Letter Drill Sizes

Tapping Drill sizes and Clearance Drill sizes for Metric Threads

Standard Number Drill Sizes

Relative Conductivity of Different Metals

Weight of Equal Steel Angles

Approximate Weight Of Round, Square and Hexagonal Steel Bars

Weight of Steel Pipes

Conversion of Gauge to Inch and MM with Approximate Weight Of Steel Sheets

Tapping and Clearance Drill Sizes for Unified Threads

ISO Metric Crinkle Washers : General Engineering

Single Coil Square Section Spring Washers : Metric Series, Type A

Single Coil Rectangular Section Spring Washers : Metric Series, Type B and BP

Double Coil Rectangular Section Spring Washers : Metric Series, Type D

Carbon, Alloy and Stainless Steel Pipes - ASME/ANSI B36.10/19

Wire And Sheet Metal Gauge Equivalents

Nema vs IEC Enclosure (Cross-Reference)

Fundamental Physical Constants

Properties of Saturated Steam

Single - Phase Alternating - Current Motors

Three - Phase Alternating - Current Motors

Arc Cutting Speeds with Carbon Electrodes

Arc Cutting Speeds with Covered Metal Electrodes

IS Fits for Basic Hole System - (IS : 919-1963 & IS : 2709-1964)

Calorific Values for Gaseous Fuels

Moment of Inertia

Chemical Composition of Common Bonding Clays

Concentration

Consumption (Volume/Length)

Consumption (Volume/Time)

Consumption (Mass/Time)

Critical Pressure Ratio Values

Conversion Factors for Units of Area (Large Units)

Conversion Factors for Units of Area (Small Units)

Conversion Factors for Units of Length (Large Units)

Conversion Factors for Units of Length (Small Units)

Conversion Factors for Units of Mass (Large Units)

Conversion Factors for Units of Mass (Small Units)

Conversion Factors for Units of Stress and Pressure (Small Units)

Conversion Factors for Units of Stress and Pressure (Large Units)

Conversion Factors for Units of Volume and Capacity (Large Units)

Conversion Factors for Units of Volume and Capacity (Medium Units)

Conversion Factors for Units of Volume and Capacity (Small Units)

Conversion Factors for Units of Heat and Energy

Conversion Factors for Units of Work and Energy

Conversion Factors for Units of Moment Force

Conversion Factors for Units of Power

Conversion Factors for Units of Calorific Value

Conversion Factors for Units of Heat Density

Conversion Factors for Units of Force

Conversion Factors for Units of Plane Angle

Conversion Factors for Units of Specific Volume

Conversion Factors for Units of Heat Flow Rate

Conversion Factors for Units of Specific Heat (Mass Basis)

Conversion Factors for Units of Specific Heat (Volume Basis)

Conversion Factors for Units of Thermal Conductance

Conversion Factors for Units of Thermal Productivity

Inches to Millimetres

Millimetres to Inches

Temperature Conversion

Units of Linear Velocity and Factor of their Inter-Conversion

Corrosion - Resistant Electrodes

Kinematic Viscosity

Dynamic Viscosity

Density (Mass/Length)

Density (Mass/Volume)

Efficiency of Various Machines

Electric Welding

Gas Welding

Gas Turbine Cycle Efficiency and Output

Estimation of Time on Different Operations

Properties and Uses of the Non-ferrous Alloys

Properties of Refrigerants

Typical Shrinkage Allowances for Important Casting Metals

Thermal Conductivity of Materials at 20o C (W/mk)

Thermal Conductivity

Steam Cycle Efficiency

Total Emissivity of Surfaces at Quoted Temperatures

Transport Properties for Air and Water

Grey Iron Castings (IS : 210-1970)

Malleable Iron Castings (IS : 2108-1962, IS : 2640-1964, IS : 2107-1962)

Carbon Steel Wire for Machine Screws (IS : 1976-1960)

Cold Rolled Carbon Steel Sheets (IS : 513-1963)

Alloy Steel Castings for High Temperature Service

Boiler Steel Plates (IS : 2002-1962)

Case-hardening Steels (IS : 4432-1967)

Cold Rolled Steel Strip for Spring (IS : 2507-1965)

Spring Steels for Use under Elevated Temperature (IS : 4454-1967)

Flame and Induction Hardening Steels (IS : 3930-1966)

Hot Rolled Spring Steel (IS : 3431-1965)

Specifications of Structural and Heat Treatable Steels

Hot Rolled Carbon Steel Strip and Sheet (IS : 1079-1968)

Carbon Steel Wire for Wood Screws (IS : 1673-1960)

Shrinkage of Materials

Steels for Hardening and Tempering (IS : 5517-1969)

Wire and Sheet Metal Gauges of U.K. and U.S.A.

Theoretical Weights of Brass Rods and Bars for Hexagons British Association (B.A.)(Imperial Sizes)

Theoretical Weights of Brass Rods and Bars for Hexagons Fractional Sizes (Imperial Sizes)

Theoretical Weights of Brass Rods and Bars for Hexagons (Metric sizes AS-2338)

Theoretical Weights of Brass Rods and Bars for Hexagons Whitworth (Imperial Sizes)

Theoretical Weights of Brass Rods and Bars for Octagons Fractional Size (Imperial Sizes)

Theoretical Weights of Brass Rods and Bars for Rectangles (Imperial Sizes)

Theoretical Weights of Brass Rods and Bars for Rectangles (Metric Sizes - AS 2338)

Theoretical Weights of Brass Rods and Bars for Rounds (Imperial Sizes)

Theoretical Weights of Brass Rods and Bars for Rounds (Metric Sizes-AS 2338)

Theoretical Weights of Brass Rods and Bars for Squares (Imperial Sizes)

Theoretical Weights of Brass Rods and Bars for Squares (Metric Sizes-AS 2338)

Theoretical Weights of Brass Rods and Bars for Imperial Standard Wire Gauges (Imperial Sizes)

Theoretical Weights of Brass Rods and Bars for Wire (Metric Sizes - AS 2338)

Theoretical Weights of Copper Rods and Bars for Hexagons (Imperial Sizes)

Theoretical Weights of Copper Rods and Bars for Hexagons (Metric Sizes - AS 2338)

Theoretical Weights of Copper Rods and Bars for Rectangles (Imperial Sizes)

Theoretical Weights of Copper Rods and Bars for Rectangles (Metric Sizes - AS 2338)

Theoretical Weights of Copper Rods and Bars for Rounds (Imperial Sizes)

Theoretical Weights of Copper Rods and Bars for Rounds (Metric Sizes - AS 2338)

Theoretical Weights of Copper Rods and Bars for Squares (Imperial Sizes)

Theoretical Weights of Copper Rods and Bars for Squares (Metric Sizes - AS 2338)

Theoretical Weights of Copper Rods and Bars for Imperial Standard Wire Gauges (Imperial Sizes)

Theoretical Weights of Copper Rods and Bars for Wire (Metric Sizes - AS 2338)