Reference charts and tables for mechanical and electrical engineering: unit conversions, material properties, wire and drill sizes, threads, steam tables and more.
Engineering Charts and Tables
- Alloy Steel Castings for High Temperature Service
- Arc Cutting Speeds with Carbon Electrodes
- Arc Cutting Speeds with Carbon Electrodes
- Arc Cutting Speeds with Covered Metal Electrodes
- Boiler Steel Plates (IS : 2002-1962)
- Calorific Value
- Calorific Values for Gaseous Fuels
- Carbon Steel Wire for Machine Screws (IS : 1976-1960)
- Carbon Steel Wire for Wood Screws (IS : 1673-1960)
- Carbon, Alloy and Stainless Steel Pipes - ASME/ANSI B36.10/19
- Case-hardening Steels (IS : 4432-1967)
- Charts - Single - Phase Alternating - Current Motors
- Charts - Three - Phase Alternating - Current Motors
- Chemical Composition of Common Bonding Clays
- Circumferential Speeds for High Speed Twist Drills
- Cold Rolled Carbon Steel Sheets (IS : 513-1963)
- Cold Rolled Steel Strip for Spring (IS : 2507-1965)
- Comparison of Hardness on Various Scales
- Concentration
- Consumption for Mass per Time
- Consumption for Volume per Length
- Consumption for Volume per Time
- Conversion Factors for Density of Heat
- Conversion Factors for Heat Flow Rate
- Conversion Factors for Specific Heat for Mass Basis
- Conversion Factors for Specific Heat for Volume Basis
- Conversion Factors for Units of Area for Large Units
- Conversion Factors for Units of Area for Small Units
- Conversion Factors for Units of Force
- Conversion Factors for Units of Heat and Energy
- Conversion Factors for Units of Length for Large Units
- Conversion Factors for Units of Length for Small Units
- Conversion Factors for Units of Mass for Large Units
- Conversion Factors for Units of Mass for Small Units
- Conversion Factors for Units of Moment Force
- Conversion Factors for Units of Plane Anlge
- Conversion Factors for Units of Stress and Pressure for Large Units
- Conversion Factors for Units of Stress and Pressure for Small Units
- Conversion Factors for Units of Thermal Conductance
- Conversion Factors for Units of Thermal Conductivity
- Conversion Factors for Units of Volume and Capacity (Large Units)
- Conversion Factors for Units of Volume and Capacity (Medium Units)
- Conversion Factors for Units of Volume and Capacity (Small Units)
- Conversion Factors for Units of Work and Energy
- Conversion of Gauge to Inch and MM with Approximate Weight Of Steel Sheets
- Corrosion-resistant Electrodes
- Critical Pressure Ratio Values
- Density for Mass per Length
- Density for Mass per Volume
- Dynamic Viscosity
- Efficiency of Various Machines
- Electric Welding
- Electrical Charts
- Estimation of Time on Different Operations
- Flame and Induction Hardening Steels (IS : 3930-1966)
- Fundamental Physical Constants
- Gas Turbine Cycle Efficiency and Output
- Gas Welding
- Grey Iron Castings (IS : 210-1970)
- Hot Rolled Carbon Steel Strip and Sheet (IS : 1079-1968)
- Hot Rolled Spring Steel (IS : 3431-1965)
- Inches to Millimetres
- ISO Metric Crinkle Washers : General Engineering
- Kinematic Viscosity
- Malleable Iron Castings (IS:2108-1962, IS:2640-1964, IS:2107-1962)
- Mass for Technical Units
- Mechanical - Approximate Weight Of Round, Square and Hexagonal Steel Bars (Inch Size)
- Mechanical - Double Coil Rectangular Section Spring Washers : Metric Series, Type D
- Mechanical Charts
- Millimetres to Inches
- Moment of Inertia
- Nema vs IEC Enclosure (Cross-Reference)
- Plain Washers, Black : Metric Series
- Power
- Properties and Uses of the Non-ferrous Alloys
- Properties of Refrigerants
- Properties of Saturated Steam
- Relative Conductivity of Different Metals
- Single Coil Rectangular Section Spring Washers : Metric Series, Type B and BP
- Single Coil Square Section Spring Washers : Metric Series, Type A
- Specific Volume
- Specifications of Structural and Heat Treatable Steels
- Spring Steels for Use under Elevated Temperatures (IS : 4454-1967)
- Srinkage of Materials
- Standard Letter Drill Sizes
- Standard Number Drill Sizes
- Steam Cycle Efficiency
- Steels for Hardening and Tempering (IS : 5517-1969)
- Table of Cutting Speeds
- Tapping and Clearance Drill Sizes for Unified Threads
- Tapping Drill Sizes and Clearance Drill Sizes for Metric Threads
- Temperature
- Theoretical Weights of Brass Rods and Bars for Hexagons (Metric Sizes-AS 2338)
- Theoretical Weights of Brass Rods and Bars for Hexagons British Association (B.A.)(Imperial Sizes)
- Theoretical Weights of Brass Rods and Bars for Hexagons Fractional Sizes (Imperial Sizes)
- Theoretical Weights of Brass Rods and Bars for Hexagons Whitworth (Imperial Sizes)
- Theoretical Weights of Brass Rods and Bars for Imperial Standard Wire Gauges (Imperial Sizes)
- Theoretical Weights of Brass Rods and Bars for Octagons Fractional Size (Imperial Sizes)
- Theoretical Weights of Brass Rods and Bars for Rectangles (Imperial Sizes)
- Theoretical Weights of Brass Rods and Bars for Rectangles (Imperial Sizes)
- Theoretical Weights of Brass Rods and Bars for Rectangles (Metric Sizes-AS 2338)
- Theoretical Weights of Brass Rods and Bars for Rounds (Imperial Sizes)
- Theoretical Weights of Brass Rods and Bars for Rounds (Metric Sizes-AS 2338)
- Theoretical Weights of Brass Rods and Bars for Squares (Imperial Sizes)
- Theoretical Weights of Brass Rods and Bars for Squares (Metric Sizes-AS 2338)
- Theoretical Weights of Brass Rods and Bars for Wire (Metric Sizes-AS 2338)
- Theoretical Weights of Copper Rods and Bars for Hexagons (Imperial Sizes)
- Theoretical Weights of Copper Rods and Bars for Hexagons (Metric Sizes-AS 2338)
- Theoretical Weights of Copper Rods and Bars for Imperial Standard Wire Gauges (Imperial Sizes)
- Theoretical Weights of Copper Rods and Bars for Rectangles (Imperial Sizes)
- Theoretical Weights of Copper Rods and Bars for Rectangles (Imperial Sizes)
- Theoretical Weights of Copper Rods and Bars for Rectangles (Metric Sizes-AS 2338)
- Theoretical Weights of Copper Rods and Bars for Rounds (Imperial Sizes)
- Theoretical Weights of Copper Rods and Bars for Rounds (Metric Sizes-AS 2338)
- Theoretical Weights of Copper Rods and Bars for Squares (Imperial Sizes)
- Theoretical Weights of Copper Rods and Bars for Squares (Metric Sizes-AS 2338)
- Theoretical Weights of Copper Rods and Bars for Wire (Metric Sizes-AS 2338)
- Thermal Conductivity of Materials at 20 degree Celsius
- Thermal Conductivity of Steel at 20 degree Celsius(W/mk)
- Total Emissivity of Surfaces at Quoted Temperatures
- Transport Properties for Air and Water
- Typical Shrinkage Allowances for Important Casting Metals
- Units of Linear Velocity and Factors of their Inter-Conversion
- Weight of Equal Steel Angles
- Weight of Steel Pipes
- Wire And Sheet Metal Gauge Equivalents
- Wire and Sheet Metals Guages of U.K. and U.S.A.